KUDP230BWH0 KitchenAid Dishwasher - Instructions

First I had to buy a new tray. I tried to remove the wheels from the old tray but they wouldn't come off without breaking. I ordered new wheels and axels and they went on fine with the aid of a C-clamp. Then I tried to remove the old bumpers but they broke when I tried to remove them.
So, I ordered two new bumpers. When I did I saw that another user had posted a note saying that the new bumpers slipped on well if heated in hot water first. So, I heated them in hot water and they slipped on easily and safely.

Loved how easy it was to deal with you!
Part was clearly pictured and came immediately!
Very satisfying to fix it so easily.
Wondered why we waited so long!

Our diskwasher is over 20 years old. The manufacture did not even list the model anymore. Googled - Kitchenaid parts old. Found your site and order the part on Sat. night. It arrived on Wed. Installed as follows that night.
After reading other reviews on how the job went and seeing that people had problems getting the tube to slide on the outlets I decided to take the rack completely apart so as to have unrestricted access to the connections. Would be easier to work the tube on to them.

First I removed the top rack by releasing the two retainers on the upper rack side rails which hold it up. Then I turned it with bottom up and released all of the plastic clips that held the bottom half of the rack in place. If a clip breaks you can use a nylon cable tie to replace it. Then I took out the screw that holds the metal water bar in place and removed it. Then I took out the screw that holds the plastic part that the water bar was mounted on off. Then with the outlet where the tube was to be mounted not connected to anything it was easy to slide the tube on it. I then was able to slide the tube on to the bracket at the back of the rack. Had to use a screw driver to help get the tube over the round outlet. Then worked it on to where it should be. Reassembled the top rack and put it back on the side rails and washed a load. It worked just like it did when it was new. Saved a service call $75.00 and only took about 30 minutes working at a slow pace.
Love it when everything works like it should.

I removed the old hose, I lightly coated the id of the new tube with vasoline, both ends, and then heated the oblong end with the hair dryer to soften it and it slid on with litte force. The round end installed without heating.

Took off old hose. It practically fell off.
Used a spoon to widen the ends of new hose and twisted on one end, then other end slipped on. Done!

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I pulled off the remains of the old tube and simply slipped the new hose on by hand. Easy as pie!

Took old one off and put new one on, about a 4 minute job.
The part was about 1/3 of the cost if I had bought it local.

removed old hose slid the new one on. Easy one minute job.

I ordered the part and I received it in just 2 days. I took the old rubber water tube off, put a little soap on each end of the new tube and had it in in under 10 minutes. I am a woman in her 60's and I did this myself!

the tube slid off and I used some liquid soap to spread on the end of each tube and I slid the new tube back on with ease and the upper rack of dishes now get cleaned/rinsed.

Took the part to the rental house and took the old water delivery tube off by hand and installed the new water delivery tube by hand , it took less than 10 minutes and exactly the right part.

Put a little liquid dish washing soap on the inside of the tube, it slipped on very easily.

it was a very easy repair thank you

I just put 1 drop of hand soap in each end of the new hose , that let it slide on EZ.