66514043K014 Kenmore Dishwasher - Instructions

I took the top dishwasher rack off, then took off the old clip I had taped on. I hadn’t watched the video so I put the new one on by looking at the other side rail and inserted the new part matching the other rail, clicked the new clip on and I was done. it was quite easy for an eighty-one year old woman!! It did take me awhile to figure it out.

Followed the enclosed direction sheet

Followed the instructions from the U Tube video by Matt from Appliance Video for Adjuster Kit W10712394. Matt did an outstanding job describing exactly how to remove the old parts and install the new ones. He speaks slowly and precisely and left no detail behind. Removing and installing the parts went like a breeze! Thank you Matt!

First remove the front kick panel by removing 2 philips screws. Turn off the water supply, and then disconnect the supply line if not of the flexible kind. Mine was copper. Remove 2 screws holding dishwasher to counter top and pull machine out. Open door and attach replacement link by hooking the plastic end to the hinge hook on the door side and then place the string portion round the plastic pulleys and then attach the other end of the link to the end of the spring attached to the rear of the machine along the bottom side. Push dishwasher back into position, reattach supply line and re-install both screws attaching the machine to the counter top. Turn on the water supply and check for leaks. Place the kick plate into postion and secure using the 2 philips screws that were removed.

The video saved me!

Remove any pieces of the rear stop by prying it off the end with small flat blade screwdriver. Make sure rack is fully on the roller tracks and then carefully push the new plastic end piece onto the rack. Be sure to orient it correctly by checking the end piece of the other rack.
I ordered two and replace them both at the same time.

Kill power to unit. Turn off water supply. Remove front access panel. Remove screw holding valve housing. Remove valve. Disconnect water lines. Replace valve in housing. Reconnect water lines with addition of thread tape. Reinstall valve and housing.

I removed the door front, unclipped the PC board cover and removed the thermal fuse from its housing. I did not splice the wires per the enclosed diagram that came with the part but unclipped the fuse from the connectors and then clipped the connectors on the new fuse and slotted the fuse back on the PC board. Put the board cover back on and then the door front. Job done.

After replacing garbage disposal. I referred to you video you sent me when i received the new replacement hose. That made it look very easy to install. Thank you for all your help and support.

Follow instructions that I found on utube. Easy repair if you take your time and follow the instructions.

I use the led indicator function to see what was the diagnostic and it says it was de circulating pump. The bad thing is you have to purchase the whole assembly they don't sell only the pump.

Then when I installed the pump it wasn't working. I had to reset the dishwasher with a sequence of the keys that you can find in the repair manual on internet. And after that started to working.

Maybe, because I am not technician it took me more than 2 hours.

Originally I ordered the rack stop clips but realized I needed the whole upper rack repair kit. It entailed pulling off parts and popping new parts on. Very easy and simple.

The kit didn't come with instructions, so I found the following YouTube video

I ordered part PS10064063, metal left and right rack adjusters that should be more durable than the plastic parts that broke. To install, I watched this YouTube video (https://www.youtube.com/watch?v=otUn8eoceBw), pausing and rewinding as needed. Piece of cake! FYI, when the axle broke, the small little plastic prongs stopped the grinder, which caused the dishwasher not to cycle. Fortunately, that was repaired under extended warranty, but the rack wheel was not covered. The repairman said the grinder (in most dishwashers these days) is a very delicate blade. They can't really grind much - even tiny plastic pieces.

Laid all the parts out after removing the old adjusting units off of the top rack. I figured out how the new parts went together and attached them to the rack and replaced the rack in the dishwasher. The instructions that came with the new adjuster kit were not much help they were hard to understand and the pictures weren’t very good easier to figure it out on my own. Hope this helps