36315461790 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Livermore, CA
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
Pump valve leaking
I disconnected the water line on the left-front. Disconnected the drain line at the air-break. I removed the AC power-in box on the right front and disconnected the power lines going to the unit. I took out the two screws holding the unit to the cabinet (above the door) and slid the unit out onto a drop cloth (protect the floor; some water spills). Pulled the unit out and turned over. Followed the directions with the motor & pump valve kit, which were very easy to follow. Then reversed the above. Nut drivers are a must for this job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Rumney, NH
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Leak
Removed the dishwasher from under the counter, found where the leak was coming from, which took the most time. We ordered the new part on line, it came the next day and the installation of the new part took about 30 minutes and the dishwasher is like new now. This procedure saved us a lot of money.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from Hughes Springs, TX
- Parts Used:
- WD28X10232
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken tower
removed old tower uuing a screwdriver to losen the tower from rack and slid the new part into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Lakeport, CA
- Parts Used:
- WD22X10008
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
cracked riser in spray arm
Ordered part Monday evening installed it on Wednesday afternoon. Required a pair of pump pliers to loosen old part, new part screwed in by hand. No leaks, no problems. Took longer to explain what caused the problem then it did to fix it. I explained to the owner that overloading the dishwasher was most likely the cause. Dishes can move or fall against the riser during wash, preventing it from dropping back down. Pulling the lower rack out with the riser bound up caused the part to crack. Thanks for the speedy delivery!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Hubbard, TX
- Parts Used:
- WD22X10008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
would not clean the dishes
I unscrewed the lower spray arm and support assembly and then screwed the new part in. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Mt. Pleasant, MI
- Parts Used:
- WD22X10008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Tower Broken
Order new part. Lightning fast delivery. Unscrew old one, put in new. 30 seconds. Don't get any easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NEIL from BOYNTON BEACH, FL
- Parts Used:
- WD28X31818
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
rusted out upper rack needed replacement
using small flat head screwdriver popped off clips at end of runners --rolled in new rack-- inserted clips back into runners
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Merwyn from Lima, OH
- Parts Used:
- WD28X10007
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
tower cap broke
simply snap new one in place. I will have to say your service was fantastic. I received the new cap 2nd day. I am very pleased and would not hesitate to order something else if needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Loring from Cambridge, MA
- Parts Used:
- WD08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
gasket deteriorated
followed the excellent instructions accompanying the gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Yucca Valley, CA
- Parts Used:
- WD22X10008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The smallest portion of the sprayer had been broken
Grab the large portion of the assembly and unscrew it- if you've got hard water, this may take some serious effort. Screw in the new part, and your good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Wichita, KS
- Parts Used:
- WD28X31818
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
upper dishrack needed replacement
In order to replace the upper dishwasher rack I needed to remove the end stoppers on the sliders. They were difficult to remove and one of them broke. I then ordered new end pieces. The new ones had been redesigned and were very easy to insert. If you need to replace the upper rack be certain to order new endpieces along with the order for a new rack. They are quite inexpensive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Burl from Spring Valley, IL
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Motor failure because of black power wire separation.
Dishwasher had flooded. Removed Dishwasher from cabinet and diagnosed problem. Found "PartSelect" on Internet and found Part kit available at reasonable price, in stock to ship immediately. Part #PS260801 [WD26x10013] contained enough parts to make installation easy and also I was able to cure discovery of slit in drain hose that attached to dishwasher drain outlet because kit included a short piece of hose and a hose clamp that allowed hose that had been trimmed to connect to outlet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Mesa, AZ
- Parts Used:
- WD08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Leaking gasket
Removed old gasket, cleaned grooves, installed new gasket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sergei from West Chester, PA
- Parts Used:
- WD08X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Replace door gasket
Removed old gasket. Then cleaned the track with a strong paper towel soaked in Windex to remove accumulated scale/soap. Followed the instructions provided with the gasket. I did not need to remove any screws from the door nor did I need to tumble the gasket in a dryer to remove kinks (There really were no kinks in the gasket, as supplied.). I did use a mirror to locate where the gasket should go underneath the bottom of the door, which you can't see. Feeling for the track with your fingers was sufficient for the installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Eastpointe, MI
- Parts Used:
- WD28X31818
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Upper rack was rusting and falling apart
To remove the old upper rack, I needed to use a screw driver to snap out the plastic end stops. That took a little time, because my dishwasher is located in a corner of my counter/cabinets, making the stop on the right very difficult to get to. Once that was done, I just slid the old rack out, the new rack in and replaced the stoppers. I was very impressed with your service and received my order in less time than stated on my order form. Will definitely use you again and recommend you to others!
Was this instruction helpful to you?
Thank you for voting!