6651770591 Kenmore Dishwasher - Instructions

I installed the opener spring in the direction it was needed to open the door then installed the pin. I placed the door in the position it goes and took a pair of pliers and squeezed the pin into the pin slot. the spring has to be forced into a tension position. I did this by sliding the spring to one side and forcing it into position, the other side is done the same way. works great

I simply looked at the remaining spring to see which notch it needed to be attached to. I went in very well using a long needle nose plier. Works great.

Unscrewed the old one and replaced it with the new one. My wife actually ordered this Pat and repaired the dishwasher.

You need a properly sized hex (Allen) wrench to get the screws out. Basically simple: remover bottom roller tray, unscrew large plastic holding bolt, remove lower spray arm, unscrew bolts (be sure the wrench is sized right or you might strip the heads), and replace gasket; then reverse procedure. Chances are if the gasket was bad, it will be very obvious (out of circular slot and stretched).

replaced the faucet adapter I did not save when I change out the kitchen sink faucet set

Put on new door, making sure the spring was set to flip the detergent door open in order for the detergent to properly do the dishes

Turn off the breaker to the dishwasher - there will be water very near the motor and other electrical components. I first scooped and towelled all the water out of the bottom of the dishwasher. The drain valve can be accessed from the bottom front of the dishwasher without pulling the unit out from under the counter. There were 4 screws to remove the 2 bottom metal panels. Next use pliers to loosen and slide back the hose clamp connected to the drain. Have a towel ready and pull the drain hose off the white check valve. The check valve can then be removed by unscrewing it - you may need to use pliers. Put the new one on and everything back together.

My dishwasher quit working the week before Thanksgiving, and to say the least, my wife was quite concerned. I did not know what was wrong, until I found the info on this website, including a how to repair video. I watched the repair video on the website when I ordered the parts. Other than my wash arm being different from what was shown in the video, it went exactly as shown in the video. I'm glad that the video, and the bag with the parts told me that there are fewer parts than originally were installed on the original. The parts looked like they had been redesigned a little, and were easier to assemble. Overall, I will be getting any repair parts I need for other appliance repairs in the future from here. Thank you for making this experience as easy as it was.

I tried going online to get some diagnostic help and never found a site that had a step by step help plan. I then did a little reading on different sites, to eliminate and perhaps diagnose my problem I use epoxy to glue the impeller(which spun freely) to the screw and it held long enough for me to see how it worked. I surfed sites to find the least expensive drain and wash impeller kit. One site had a cheaper price but I chose Parts Select because of the shipping so the end result was the best results for me. I am not sure but the estimated time was 1.7 or 1.8 days delivery that I did not believe would happen. When I received the parts and did the repair my final time from ordering was less than a day and a half. I could not have done the job myself without the video because the parts were very different. My biggest obstacle, other than my ignorance, was some sort of chemical on the screw that would not allow me to loosen it. I used a dremel to cut the head off and then a torch to heat the stub so I could remove it. After I received the kit I saw a chemical on the screw threads so online research told me heat loosens the chemical. My dishwasher is around 25 years old,I have worked on it three times now and replacing the impeller was the most difficult task to date. Should it last and develop another problem I will go to parts select first and start my quest.

I looked in the bottom of the dishwasher after browsing the website regarding possible solutions. When I removed the bottom spray arm I noticed three screws missing from the pump housing. The loose pump outlet had allowed the seal to push out. Ordered-Normal shipping on the part.

I ordered the parts on Fri. and they came on Sat. Thanks. I had to pull the dishwasher forward about 6". Then just put the springs on. They don't have much tension with the door closed. Easy. Thanks again.

The dishwasher was making grinding noises and then stopped draining at all. I was able to follow the video directions and replace the parts from the drain and wash impeller kit, but it did not solve the problem. Must be the pump or something else. Was worth a try and partselect.com was good with service and price.

Heard a grinding noise in our dishwasher one night recently while it was in the drain mode. Water wasn't draining out so I had to siphon it out with a tube, cup, and rags, then looked up information about the washer/dryer on the internet and found PartsSelect. I watched the repair video they provided and decided to give the repair a try. I began to remove all the necessary parts following the instructional video.
The hardest part of the job came early on, and once that was completed the rest of the job was a cinch. The center screw holding the upper impeller was the hardest part to remove. I tried to use the adjustable wrench on the hex shaped nut molded to the impeller while turning the screw, but that old screw was so tight I was afraid I'd strip the molded impeller nut.
I then tried a 1 inch nut without the driver attached to it but with a pair of vice grips clamped at about 45 degree angle on the 1 inch nut and set on the molded impeller nut while at the same time trying to remove the screw by putting the small nut driver through the top of the 1 inch nut and turning it. No luck there either. It would not budge.
By this time I was entertaining the idea of buying a new 5 to 800.00 dishwasher.
Well I had nothing else to lose except 5 to $800.00, so I reverted to caveman technology.
I ended up using a small chisel and wood mallet to get the impeller off the shaft. Since the impeller is made of a rubber like material, it came off easily in pieces using some careful strikes with the hammer on the impellers molded nut. When this was complete, I unscrewed and removed the filter housing.
The impeller screw, which was still in the motor shaft, and was removed 'after' this because there was no impeller or filter chamber in the way. There was a small space between the screw and the motor shaft since the impeller was removed from around that screw so I first tightened it a little bit, then finally was able to loosen the screw. You would think that screw had been super glued into that shaft but it finally came out. After that I removed the chopper blade and found that the spring attached to it was bent and had tore the shaft of the 'lower' drain impeller to pieces. After cleaning up the impeller pieces I ordered the drain and wash impeller kit from PartSellect. It arrived in a couple of days and the new parts installation went quickly.I was especiially relieved that the new screw and impeller went on without a hitch.
I didn't use the new shaft seal provided because it was a different height then the original seal and wouldn't allow the cover to the drain impeller to seat properly. The height of the new seal also caused the new drain impeller to push or spring up too high.The original seal looked fine so I used that and it worked just fine also. Started the dishwasher up for a test and it all worked flawlessly. No noise no leaks. This was my first washer dryer repair. Following the Part Sellect instructional video with Steve explaining while doing the removal of old and installation of the new parts was a breeze. SO, here's my conclusion. Folks, for under $50.00 I saved a lot of money and expect that I'll get at least a few years more use from this old dishwasher. Thanks again to PartSelect and Steve for your help.

The video was great! I couldn't have done it without it. The repair took me a little longer than expected because I did not have the right tools (torx head screwdriver), but once I went out and bought it, the rest was fairly easy. The old impeller had some build-up on it, so it was pretty hard taking it off the motor shaft: this was one of the hardest parts, since I was afraid of forcing it out and breaking something. Once I cleaned up the motor shaft, however, the new impeller went in easily. Both the old impeller and washer seal were damaged. Overall, I was very happy with Partselect's fast shipping, easy-to-use website and incredibly helpful installation videos. The machine is now not only NOT leaking anymore, but dishes are coming out MUCH cleaner. The dishwasher is over ten years old, so I was happy that this low-cost fix made such a big difference and we didn't have to buy a whole new dishwasher.

The repair was fairly simple and made easier with an installation video. The repair went well and there's no more leak.