66515119K216 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Johanna from JOHNSON CITY, TN
- Parts Used:
- WPW10498900
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Middle spray arm would not turn
I broke it accidentally while trying to get it off and it would either not spin or fall off. I simply removed it out of the box and put it on. 2 turns to the right and I was done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from BATON ROUGE, LA
- Parts Used:
- WP8268961
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher door drops quickly to wide open position when unlatched
Rubber friction sleeves on each side of the door provide resistance to prevent the door from quickly opening when unlatched. Over time the friction sleeve may crack and fail. Two friction sleeves are required for repair. Install a new sleeve on each side of the dishwasher door near the spring connector at the bottom.
Open dishwasher door.
Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.
Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.
Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.
Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.
Repeat for right side of door.
Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.
Slide the dishwasher back to the original position under the counter top.
Insert the screws in the top brackets to secure the dishwasher.
Open dishwasher door.
Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.
Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.
Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.
Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.
Repeat for right side of door.
Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.
Slide the dishwasher back to the original position under the counter top.
Insert the screws in the top brackets to secure the dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeffrey from HOUSTON, TX
- Parts Used:
- WPW10491331
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Poor to no cleaning lower basket
lower wash arm cracked by spinning into items hanging out of bottom of basket. part twists and snaps right in. glue did not fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from MILLBURY, MA
- Parts Used:
- W11175771
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Dishwasher wasn’t getting water.
I located the water inlet valve underneath. After moving the dishwasher out from the cabinet, I tilted it . Then I disconnected the black hose with the pliers . Using the adjustable wrench I unscrewed the water feed to the valve . I then unscrewed the valve from the frame and disconnected the wire plug by unlocking and slipping it away from the valve. To install I did all this in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ginger from DONIPHAN, NE
- Parts Used:
- WPW10491331
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
top of spray arm separated from bottom causing not to hold pressure and spin
Pulled up old spray arm and snapped new on in place. Took less than a minute and no tools. Dishwasher is like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from GLADSTONE, MO
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Front Track stop missing
Snap new track stop into place. Took a few minutes to figure out top/bottom and inside/outside, but no issues
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from PEMBROKE PNES, FL
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Top rail stop clip broke
Very easy to remove the broken one and just clip in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from VAN BUREN TWP, MI
- Parts Used:
- 4317824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
none
removed and installed cords with screw driver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from DOWNS, KS
- Parts Used:
- 4317824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Someone had used the wrong type of power cord
Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from SANFORD, NC
- Parts Used:
- W10846093
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Old recirc pump failed
It is a bit difficult to align the grommet, hose, and mounting arm. Suggest using a little vasoline in bushing for the mounting arm/support. it really helps slide in the arm into that bushing so you can get the grommet and hose lined up.
Also, instead of using the supplied hose clamp, suggest using an automotive style hose clamp if you don't have the special tool for tightening the supplied clamp.
Also, instead of using the supplied hose clamp, suggest using an automotive style hose clamp if you don't have the special tool for tightening the supplied clamp.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from MILWAUKEE, WI
- Parts Used:
- W10518394
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dishwasher would not start & green "Clean" light was flashing
After reading customer notes regarding the same problem I was having I ordered A new Heater Element & a High Limit Thermostat. I also ordered a Heating Element Nut and Rubber Washer in case I needed them. It took me quite some time to remove the dishwasher from under my counter. Once the unit was out and prepared to service it actually took only a few minutes to install the new Heater Element. I did't need the washer or extra Nut. I also decided to try the unit without replacing the thermostat. I cleared the diagnostics by pressing the "HEATED DRY, "NORMAL", "HEATED DRY", "NORMAL" buttons. After the controller reset the dishwasher was ready to run.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Springhill, FL
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
element not working
laid dishwasher on its side and unscrewed element. returned unit upright & replaced element. reversed process and reinstalled unit under cabinet
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Des Moines, IA
- Parts Used:
- 8269144A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Dish washer was very smelly.
After replacing garbage disposal. I referred to you video you sent me when i received the new replacement hose. That made it look very easy to install. Thank you for all your help and support.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from DEVINE, TX
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Wrench (Adjustable)
Element was no longer working. Dishes were not drying.
Watched a video and seen how easy it was to repair. Just disconnect the power, water and return drain. two bolts and replace element . The difficult part was removing and replacing the dishwasher...piece of cake.
Was this instruction helpful to you?
Thank you for voting!