66513472N410 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Roy from HIGGINSVILLE, MO
- Parts Used:
- WP8269145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken Mounting bracket
Removed old part and replaced with new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LINDA from ROSEVILLE, CA
- Parts Used:
- WP8268961
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door had no resistance when opening it
You only need to pull it out about 6 to 8 inches and you don’t need to disconnect anything to slide it on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from ALTADENA, CA
- Parts Used:
- WPW10491331
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
After cleaning the filter basket & metal grill (floor of dishwasher), I neglected to secure the bottom spray arm. It came loose, landed on the heating coil, and melted.
I simply removed the melted spray arm, then set the new spray arm in place, twisted the built-in securing nut (clockwise to its stop), and it worked without any problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SAINT CHARLES, MO
- Parts Used:
- W10872845
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
New filter
Ordering the part was very easy. It shipped fast and delivered over 3 days. It fit perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dwight from KENT, WA
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
One of the old stops broke
Snapped the new stops on. It took about 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from U SADDLE RIV, NJ
- Parts Used:
- WPW10463906, WPW10491331
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishes were not getting cleaned and water was coming out the bottom of the door
The top and bottom parts of the lower wash arm were separating. This caused water to spray out the ends of the wash arm and come out the front of the dishwasher. In addition this water was not spraying upward resulting in dishes not getting cleaned. Took me a while to figure this out but the repair was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Giorgio from Savannah, GA
- Parts Used:
- 8269144A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench set
Drain hose broken.
Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Daleville, AL
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
The dishwasher would not dry (heat)
First I identified the problem by checking the plug ends of the heater coil with an ohm meter. I quickly odered the part and when it arrived a few days later, I simply pulled off the electrical connectors, unscrewed the two bolts, removed the old/broken coil, put in the new coil and tightened down the nuts snuggly.
Nothing to it. I then had to reset the error code and it is working like new.
Nothing to it. I then had to reset the error code and it is working like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from REIDSVILLE, NC
- Parts Used:
- W11086533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Needed a tub sound shield
All I had to do is lay the shield over the top and sides and used a couple of clips to hold in place as it was slid under the counter top. It couldn’t have been easier.We had searched everywhere for this replacement shield and parts select was the the only ones that had it. Very good service and fast delivery,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from AUBURNDALE, WI
- Parts Used:
- WPW10195039
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
water fill overflows at times
thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and install new switch and reconnect the wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vivienne from GILLETT, PA
- Parts Used:
- WPW10491331
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Arm sprayer had broken
Something had been loaded in the dishwasher that had gone thru the basket - it hit the arm sprayer and broke it off.
Replacement sprayer was exactly the same - the partselect website has very specific identification method so you get the proper part. You must have your model number.
I watched a you tube video which was referred by part select. This was helpful.
I did not realize at first that only part of the arm sprayer had broken off. The arm sprayer broke off, but there is a base to the arm sprayer that was still attached to the dishwasher. So I could not, of course , fit the new arm with its base over the existing base because they are the same size. Once I realized this, it was a simple replacement, following the youtube instructions. You do have to press and turn counter clockwise to get the old base off, but once that was done, the new sprayer arm, which arrived attached to the base, easily fit, and press hard to turn it clockwise to reattach it..
It has worked perfectly. It is a hard turn to get the arm sprayer off or on, which is good so it doesn't come loose during washing, but when replacing it, you aren't sure of why it won't turn. It is a hard turn. Watch the you tube video.
Replacement sprayer was exactly the same - the partselect website has very specific identification method so you get the proper part. You must have your model number.
I watched a you tube video which was referred by part select. This was helpful.
I did not realize at first that only part of the arm sprayer had broken off. The arm sprayer broke off, but there is a base to the arm sprayer that was still attached to the dishwasher. So I could not, of course , fit the new arm with its base over the existing base because they are the same size. Once I realized this, it was a simple replacement, following the youtube instructions. You do have to press and turn counter clockwise to get the old base off, but once that was done, the new sprayer arm, which arrived attached to the base, easily fit, and press hard to turn it clockwise to reattach it..
It has worked perfectly. It is a hard turn to get the arm sprayer off or on, which is good so it doesn't come loose during washing, but when replacing it, you aren't sure of why it won't turn. It is a hard turn. Watch the you tube video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from WESTERVILLE, OH
- Parts Used:
- WP8565925
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rollers broke off top rack assembly
Replacement parts from factory installed using u tube support video
Also replaced stop ends for top rack by removing old clip in to push down and lined up to secure in slots at end of rack, notice new plastic parts are installed by pushing hardware into slots downward until they clip into place
Also replaced stop ends for top rack by removing old clip in to push down and lined up to secure in slots at end of rack, notice new plastic parts are installed by pushing hardware into slots downward until they clip into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from HUDSON, NC
- Parts Used:
- WPW10348269
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
pump not working
Looked on you-tube and it was so easy. Pump on bottom right. unplug pump and do a halfway turn. Plug the new one up and place the pump on, and turn halfway and its on. START your dishwasher
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brad from ABILENE, TX
- Parts Used:
- W10537869
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The diverter motor was leaking
Actually, I found a video on Youtube with excellent instructions once you got past the really simple stuff like disconnecting power and water and drain.
I would recommend just finding a fairly similar model on Youtube and follow their directions. It was really easy.
I would recommend just finding a fairly similar model on Youtube and follow their directions. It was really easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from FORT MYERS, FL
- Parts Used:
- WPW10348269
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dishwasher would not drain properly due to broken impeller in the pump. Could hear and feel vibration thru pump body.
Followed the easy how-to video from PS. It was as easy as changing a light bulb.
Was this instruction helpful to you?
Thank you for voting!