66513472N412 Kenmore Dishwasher - Instructions

This wheel mount broke from normal use and made the upper dish rack disconnect from the sliding arm that extends it outside the dishwasher body so that you can fill it. The part was delivered quickly and was easy to install using just a screwdriver to loosen the retainer clip on the end of the extension slide. Once the retainer clip was removed, the new part was slid into place and clipped onto the rack. The install was complete.

I had to fiddle with the mount a bit to get it on the rack properly. Then I pulled back slightly on the inner part of the end piece of the track while also pulling the top of the piece back and released the inner tip of the piece, allowing the end piece to be removed. I placed the new wheel in the track and replaced the end piece.

Super easy and a small fraction of what a repairman had told me the part would cost.

Step 1: Remove the screws in the bottom of the countertop.

Step 2: Remove the screws holding the bottom kickplate.

Step 3: Loosen leveling legs.

Step 4: Pull dishwasher out of hole.

Step 5: Unlplug dishwasher.

Step 6: Disconnect wires from bottom of element in back.

Step 7: Remove plastic nuts holding element in place.

Step 8: Remove element.

Step 9: Reverse Steps 1-7.

Step 10: Drink beer.

Each Molded one-piece plastic upper dishrack wheel mount includes a tiny plastic spring clip which hold the mount in place on the upper dish washer rack.
These clips become dry and britle over time and snap off.
Because they are molded in the wheel mount itself you have to replace the entire wheel mount assembly

I called an experienced plumber, who balanced and installed my new dishwasher properly, using the brackets I ordered from Parts Select, after an INEXPERIENCED plumber had tossed the factory-provided mounting brackets out with the shipping carton. Relief!

the parts only took a few days to arrive, and it took me about 2 minutes to install them-no tools were required. i took out the end plugs from the slider bars, slipped out the old broken wheel parts, snapped on the new ones, slid the upper rack into the slider assembly, popped the end plugs back into place and VOILA!!

aside from the expense of the parts- much better to go this route rather than hire a repair guy to do it!!

We replaced all four. You unclip the two front parts on the top drawer to pull it all the way out of the dishwasher. Unsnap the old mounts and clip the new ones on. Slide the top drawer rack back in and replace the two front clips.

This was truly an easy repair!

Took stop off end of track by smooshing spreader things together with butter knife, so they would fit through holes.
Maneuvered wheel on track and clip on rack. Put the stop back on.

My filters had completely clogged up and had not cleaned my filters at all which was a no-no.I had lots of food left on the dishes after running my dishwasher, so I took bothp filters out and replaced them no tools required. I won’t be using powdered or liquid detergent for my dishwasher anymore only pods and promise to clean my filters once a month, so hopefully that’ll help keep them clean. Very easy replacement even for an old woman.

After shutting off electricity, lay dishwasher on it's side (use a towel to absorb any water) then just use nut driver to remove faulty valve.

unscrewed dishwasher from cabinet ...,moved out slightly....while door closed ...reached with long nosed pliers door spring pulled forward...and allowing white plastic part that fits through sleeve and fit new sleeve over it...pulled spring attaching white plastic part and pushed unit back to cabinet and replaced screws DONE.

I shut off the power to the dishwasher, then I removed the front panel under the door. On the right side just behind the electrical box there are two wires going up to the hi-limit thermostat, (you may need a small mirror to see it), remove one screw that is holding the thermostat bracket, unplug the wires from the old thermostat and install new one. Screw bracket and thermostat back to the underside of the dishwasher, reinstall the front panel, turn on the power, done.

Unplug the dishwasher,take the screws out of the coutertop,then slide dishwasher out turn it on its side. Then take a torx screwdriver and remove 2 mounting screws. Unplug the wires going into the motor and replace the motor with the new one. But you need to replace the grommet the motor shaft slides up into or it will still leak.

I purchased this misguided by the official response to "Doug" on April 17, 2018, which at the time was labeled as "most helpful". This is NOT the little grommet in the center. This is a big grommet that goes no the supply pump. This is #14 in the diagram. (#15 is actually the clamp that holds it). If you are looking for the little grommet that goes on that stem on the central recirculation pump, that part is not available, it only comes fused on the sump, and for replacing the sump you have to disassemble the whole bottom part of the dishwasher, pumps, sensors, valves, hose...even this big grommet. A lot of work, and since you are at it, you might want to replace both grommets. If you need THIS big grommet (#14) only, then it is not so much work, just take out one clamp, one connected cable, and the grommet to replace. But check if your machine has reusable clamps, because if not, you might want to order a new clamp. Good luck!

Put thread tape on threads. Screwed water hose to part. Pushed hose onto part. Pushed electric clip to part. Screwed part onto washer. Done