66513222N410 Kenmore Dishwasher - Instructions

After I finally got the right parts and installed them I discovered that even though I had bought the OEM part for my dishwasher it not only didn't fit but prevented me from even getting the upper rack back in the dishwasher. The dishwasher won't work with out the upper rack properly in place. Every part store I looked at offered the same part for my dishwasher so obviously Whirlpool made a huge mistake. Since it's not possible to get the old parts back on (one of them was broken anyway which is what started all of this) I had to buy a new dishwasher. I did contact Whirlpool by email but got no response. If you own a Whirlpool dishwasher be very cautious buying any replacement parts.

I followed the wonderful videos provided with the part and fixed the problem easily! I suggest making a separate instructional video on how to get the dishwasher out of the housing.

Initial inspection of the issue and research suggested the door latch was malfunctioning / broken. I bought the part and expressed it home. The installation involved removing the door screws on the inside of the door, separating the front and back panels, unplugging the door latch, removing it from its niche and popping in the new one. Reverse the take apart and it was done. Very simple swap. Hardest part was juggling the two halves of the door and preventing the door for trying to close in the process as the bulk of the weight is in the outside half of the door.

The new part did not fix the issue. The door strike was the next part that could be broken / malfunctioning. I ordered that part as well and replaced it. In the process of replacing it I found that the original door strike had been installed upside down. I am guessing it was installed at just the right pitch, or maybe even bent at the manufacturing facility, so that it latched. No idea how it managed two years like that. I installed the new one correctly and the door latches perfectly. Both parts I removed from the unit I will retain if my new parts should fail in the future.

leveled dishwasher, it was leaning forward, raised front 1/2'", to get level.
no More leaks, WOULD LIKE TO RETURN DOOR SEAL. DID NOT USE SEAL.

THANKS,
PETE GODSHALK

The 1st person i had contact with wasn't any help choosing the correct part. Paid about $30.00 for the wrong part. Paid $8.00 more to ship the wrong part back for reimbursement. Meanwhile my son went to a local repair shop and got the right part for less than $40 and the repair shop installed the part on the rack for free
I was not happy with Part Select! Part Select cost me time and money and didnt get the job done

Due to the way I installed the appliance originally it was not necessary to disconnect supply water nor the drain connections. When the cord broke the spring came out of the point of connection to the appliance. It some "finagelling" to reattach the spring.After some "select vocabulary" it hooked into the correct spot and the rest was history.

I took the valve off and actually hooked 110 volts to the vale and tried to blow through it and it would not let air pass through it. I replaced the the new valve in about 15 minutes and it works fine

There were no instructions with the kit so I went online and watched a How-to video so I could fix it. However, the new white wheels were too big so I had to use the wheels from the old rack.

Replaced the strainer. This keeps the two sprayers clean/clear so they do not clog up. Dishes are cleaner now. Note : if your sprayers are clogged it is a long process to clear out the sprayers. Dishes will not be clean until your sprayers are all cleared.

Pulled washer out far enough to put 2x4’s under front feet. Removed front panel, I clipped wire connector and unplugged it. Pushed plastic locking lever in and twisted unit counterclockwise. Wiped inner rim and reversed above procedure to assemble.

The old filter simply unscrews and the new one screws in.

The air just unscrews with one twist and the new arm twist right back on. No tools needs. Saved me $100 service call.

Top of stop slides on and push bottom in ,will click

I had a common issue on many dishwashers, the final drain cycle was not draining but the pump was trying to turn. Also, the drain pipe was clean. This issue caused a burning smell, like a circuit board heating up. Half plastic smell, half electrical. I bought a replacement pump, followed the pump replacement video instructions from PartsSelect, and it was replaced in under 15 minutes without any tools.

These wheel assembly that came on the lower rack of my dishwasher were junk! They started falling off within 6 months. I put them back on to the point that the pin in the center of the wheels would no long stay in place, thus the frustrating situation of the wheels falling off often.

Assembly was easy peasy!