66513222N410 Kenmore Dishwasher - Instructions

placed sprayer arm in position and twisted it into position, about a 1/4 turn, snaps into place. total of 15 seconds!

Hardest part was pulling dishwasher away from cabinet, making sure to not disturb water and drain line. I replaced both door springs which are on the two sides and attached to the dishwasher frame towards the back. This necessiatated pulling the dishwasher about 2/3 out of cabinet. After attaching both springs to frame, replacing the balance kit was a breeze .One screw to remove and then replace with new pulley unit. Attach the supplied cord with attached fittings to spring and then around two pulleys and mounting point on frame. Done . Push dishwasher back into cabinet, reattach two screws to underside of counter. Probably did not require new springs as they seem heavy duty and were not broken upon examination but ordered them also and replaced just in case. Most problem would be with broken cord in balance link kit

thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and install new switch and reconnect the wires.

The water valve float lever was broke. So I replaced that and the water level switch. Probably didn’t have to replace switch. Very easy!!

Looked on you-tube and it was so easy. Pump on bottom right. unplug pump and do a halfway turn. Plug the new one up and place the pump on, and turn halfway and its on. START your dishwasher

simply line up the new pin with the rectangular slot in the kick panel and metal panel behind, slide the pin in and turn it with a flat blade screw driver.
NOTE: the original pin was black. A black replacement part cost $29 plus shipping! A knock-off pin was only $6 plus shipping. I got the cheap one and colored it with a black Sharpee marker before installation.

After I finally got the right parts and installed them I discovered that even though I had bought the OEM part for my dishwasher it not only didn't fit but prevented me from even getting the upper rack back in the dishwasher. The dishwasher won't work with out the upper rack properly in place. Every part store I looked at offered the same part for my dishwasher so obviously Whirlpool made a huge mistake. Since it's not possible to get the old parts back on (one of them was broken anyway which is what started all of this) I had to buy a new dishwasher. I did contact Whirlpool by email but got no response. If you own a Whirlpool dishwasher be very cautious buying any replacement parts.

replaced the whole bracket assembly very easy to do.

The upper rack adjuster kit was replaced exactly as the video showed. I felt it was not very complicated and the new parts look more hefty then the original parts.

Front track stops was just a matter of snapping them into place.

Pulled off old seal. Pressed into groove the new door seal. No parts required.

Husband watched your repair video. Everything went well and we are very pleased.

Pull the old seal out and push the new seal in. Done. Easy. The only issue is the door is still leaking and I have to replace the seal and the plate that goes across the bottom of the door.

Order both this seal and the seal for the bottom of the door at the same time.

1) clear out the dishwasher
2) remove unit securing screws from top or sides of DW and cabinetry near the top or under the counter top
3) gently pull the dishwasher from the cabinetry about 20" is plenty, mind the connecting hoses and electrical connection
4) close the door! pull back the insulation from the area of the hinge and photograph both sides - this will save you the pain of going online
5) you will see the cord, the tensioning wheel assembly and the door balance spring on both sides
6) with the door closed to relieve tension on the cord, remove the cord from the balance spring - this can be done w/o tools at this point
7) remove the 5/16" screw from the plastic tensioning wheels and remove the tensioners, cord - leave the springs in place if not replacing them
8) install the door end of the cord to its hook on the hinge, install the new tensioning wheel assembly, install the old 5/16" self tapping screw through the lower wheel and into the outer hole in the frame
9) thread the cord from the door over the upper wheel and lower wheel. the lower wheel has cord retaining tabs to hold the cord on the assembly
10) hook the eye end of the cord to the balance spring and you are finished with the first side - repeat operations for the other side, reposition the insulation and slide the washer back in its cavity - do not forget to reinstall the stabilizing screws in the upper washer frame
11) you've done it!
12) have a cuppa and do your second washer that hasn't failed yet - it will soon.

Follow the u tube instruction. Replacing the pump was very simple and easy. The hard part was getting the dishwasher out of the cabinet and back in again.

The repair was similar to the very good video provided by PartSelect. However, I did make a few changes. The new rack was slightly different in the front side compared to the old rusted rack. After I removed the old rack from the dishwasher, I placed the two racks side-by -side to make sure they were compatible. They were identical in the rear structure and overall size, so I proceeded to change out the wheel racks, rack height adjusters and upper wash arm to the new rack. I suggest transferring each part one at a time so you can get the spacing correct. Also, in my case, many of the items needed to be washed with water to remove soap buildup in these parts before moving to the new rack. I would also suggest putting the upper wash arm (needed in this case) on the new rack last. The total job took me about an hour including washing or rinsing all parts and reassembly. This is an easy job, just take your time and do one item at a time so nothing gets mixed up. I used a drill driver to remove a total of 4 Phillip head screws for the rack height adjusters but a regular Phillip head screw driver would work as well.