66513222N410 Kenmore Dishwasher - Instructions

repair was easy. Pictures in the instruction not clear had to refer to old parts

Follow directions

I removed the old gasket. Cleaned the surface under the old gasket and began pressing the new gasket into place. Make sure the gasket is pressed all the way in to properly seat it in the groove. Didn't use the tube of gasket sealer and it worked perfectly no leak,

change out the old pump with new one actually quieter running pump awesome

I watched the video and this was the easiest repair ever. Took longer to disconnect and reinstall than it did to change out the pump. Highly recommended watching the video

Shut the power to the dishwasher off. Pulled unit out from under the counter top and raised the left hand side up for easy access. Disconnected the wiring, undid the clips, turned counter clockwise and removed. Reversed the order for installation and Connected the power. Ran several cycles successfully. Problem fixed. Burnt out water pump. Good as new if not better so far. Easy item search, Fast Shipping, Quality Part, Fair Pricing. Thank You Partselect.com

Removed bad wheel sets using screw driver to help pry broken part loose. Then just snapped in replacement. Took less than 5 mins. Now it works great.

I followed the directions on YouTube and the paper that came with the part. The only problem is the 'little tabs' that they act like are easily pushed are rather more difficult since you don't want to break the things off.

I found instructions on line when I goggled my dishwasher name and model number with the words noisy door. There were three or four good suggestions at a couple of the sites I visited. I tried applying vasoline, then silicone to the rope where it travels through the plastic guides but that just cut the sound down about 50%. My dishwasher has plastic guides that look like rollers but they don't turn, they are fixed in place. The ropes squeak as the pass over the guides. The replacement part kit has plastic guides that turn like wheels now so the rope does not drag over them and squeak. This repair could be done by me in 20 minutes or less every time now that I know what I am doing.

I removed the black bottom metal cover then turned the nuts on the adjusting (leveling) bolts to lower the front end of the dishwasher so I could pull it out of the cabinet. Once I lowered is as low as it would go I opened the door and pushed down on it which tilts the dishwasher down and you pull out on it and the top lip clears the cabinet. If your dishwasher just pulls out the first time you try these steps may not be necessary.
Once the dishwasher is out the guides and rope are down at the bottom in the front by the door. It's obvious what to do to replace them.

saw big hole in first (main) hose - got replacement at local hardware thinking it was the only problem - it wasn't - turned on the water and noticed another leak so ordered hose from parts select - fast delivery - installed 2nd hose but still a leak so ordered grommet from parts select - again prompt delivery - installed it and voila no more leak -
also checked for rat entry points, plugged those and put down bait - bait wasn't being taken under dishwasher even tho rat reappeared so put a snap trap in back - no luck so far - teachable moment: might have been cheaper to just get another dishwasher as parts are expensive and its difficult to tell extent of damage - luckily i only needed 3 parts = $150

The repair was really easy. First disconnected electricity staring with fuses and removing wires from dishwasher, then disconnected drain hose and water hose. Pulled it out and removed pump turning clockwise no need for tools and same way installed new one. Very easy

Was a cinch just watched the video whole procedure took an hr or so

The cost part plus shipping for each piece which was described as not cleaning properly due to not spraying. Each of these prices is part plus shipping, diverter valve $28.32 diverter motor did not fix the problem diverter motor $125.08 did not fix the problem my next option is the motor assembly which comes out to $311.53. I think they lead you on with the little parts and you work your way up with the big ones expense wise at this point I will simply cut my losses and buy a new dishwasher because I'm almost at what it would cost for a new one and I've had this one for 4 years. When I went to look for what the problem was each one of these said not cleaning properly which I think now is a generic term to just go from the smallest to the largest if I'm going to replace the motor for 300 plus dollars I might as well just buy a new washer

removed old gasket, installed new.
No Leaks!!
Saved the cost of a new dishwashers

You need to pull the unit out to get access to the spring connected to the rear leg frame. Use the everything in the kit. The rollers are upgraded and will guid the cable better.