66513259K111 Kenmore Dishwasher - Instructions

Remove power source, then remove old power cord.Run new power cord through existing opening ang attach to existing power box on bottom o f dishwasher. Install electrical leads and device ground. Reinstall cabinet bottom. Check out operation by running a cycle. All ok!

1. Remove the top rack
2. Take a screwdriver and pry off back plastic stop at end of track
3. Slide track off, then slide new track on
4. Take the plastic back stop originally pried off of old track and snap into new track
5. Open plastic stop at front of track
6. Replace top rack.
7. Close plastic stop at from of track
8. Good to go!

I removed the upper rack and unclipped the roller assembly and snapped the new ones in place.

followed directions, a kid could have done it,

Very, Very easy - watched the Installation Video highlighted on web page and the entire process took less than 5 minutes!

Removing and installing the new part was fairly simple. We removed the water hose first since it is the easiest to see. We then removed the screw holding the part to the metal frame. We slid out the part out of the holder to remove the black hose and electric plug (it is like the old phone jacks). After it was completely off we plugged in the electric to the new part which was very easy since it can only go in one way. We slid the new part in place and attached the black hose. We attached the piece to the frame with the one screw and last we attached the gold (garden hose) connection. We turned on the water to look for any leaks then turned the power on and ran it through a partial rinse to be sure there were no leaks.

easy - plastic snap in part

based on advice here, concluded the problem was likely that the part "Valve-Inlt" was defective. Our dishwasher intake line is copper and had already developed a partial kink from sometime in the past, so I had to be careful. The final connection to the new part had to happen in place: very close to the floor and underneath, because I didn’t want to stress the copper line. Plus, the shutoff was defective, and it was always leaking while I connected. Awkward. As I was threading on, it started to look like it might be cross-threaded, so I stopped and reversed. Slid the washer back out and disconnected the drain line so I could tip the dishwasher u and inspect. It was going on cross-threaded. Not hard to happen on a metal to a plastic connection. To solve, I carefully made very small bends in the copper inlet line until when it would later be brought up underneath to connect to the inlet valve, it would be as perfectly aligned as possible. This worked. As I tightened, it went a little easier and the leak stopped. A good moment. Tightened a bit more, but didn’t want to overdo it as that can cause other problems. Now the moment of truth: let’s run it. DISHWASHER WORKED AGAIN. Runs fine now and we are glad to have it back. Was satisfying I could do this on my own. The advice and guides here made that possible. Thank you.

It took all of 30 minutes from beginning to end remove the old parts and replaced them and run a diagnostic test before I could wash dishes. The parts were exact and Parts Select has always provided the right parts, shipped fast and never disappointed me.

Stared at it and deduced that the clip was not intended to slide into the track from the end, but that it was intended to snap in from the side. NO WHERE WAS THERE A SINGLE SENTENCE TELLING HOW TO DO THIS. And don't give me the old bromide, "Well, everyone knows how to do this." Nope, It is not in my DNA, so a sentence included with the clip in the package would have saved me time and pain.

Took off the broken part replaced it with new part.

I'm the maintenance supervisor at an apartment complex. While installing a new dishwasher for a tenant, I inadvertently cross-threaded the swivel connector to the fill valve. The valve was ruined and couldn't be repaired. I ordered a new valve (it was an OEM) and installed it. Simple switch out, plus the video from Parts Select showed I had done it right.

Replaced the wheels.

Popped the old clip out, replaced with new.

I first verified that there was 120 volt line voltage getting to the unit. I removed the outer door panel by removing the 10 torx screws located around the panel on the tub side of the door. Two of the screws are longer so note there location for reassembly. The door handle can now be removed. Pull the outer door panel away from the inner panel and remove the connector to the control board. Set the outer door aside. Remove the connector to the door latch.The latch is snapped in position at the top side. Pry using a screw driver to release. Snap new latch in position. Snap on connector, Reassemble door by first reconnecting the control panel connector. install plastic door handle. Mate door to inner panel. Note interlock tabs between outer door and inner panel near the bottom area. Install the 10 screws. The two longer screws are at the top holding the latch and handle.