66515692K212 Kenmore Dishwasher - Instructions

placed sprayer arm in position and twisted it into position, about a 1/4 turn, snaps into place. total of 15 seconds!

1) clear out the dishwasher
2) remove unit securing screws from top or sides of DW and cabinetry near the top or under the counter top
3) gently pull the dishwasher from the cabinetry about 20" is plenty, mind the connecting hoses and electrical connection
4) close the door! pull back the insulation from the area of the hinge and photograph both sides - this will save you the pain of going online
5) you will see the cord, the tensioning wheel assembly and the door balance spring on both sides
6) with the door closed to relieve tension on the cord, remove the cord from the balance spring - this can be done w/o tools at this point
7) remove the 5/16" screw from the plastic tensioning wheels and remove the tensioners, cord - leave the springs in place if not replacing them
8) install the door end of the cord to its hook on the hinge, install the new tensioning wheel assembly, install the old 5/16" self tapping screw through the lower wheel and into the outer hole in the frame
9) thread the cord from the door over the upper wheel and lower wheel. the lower wheel has cord retaining tabs to hold the cord on the assembly
10) hook the eye end of the cord to the balance spring and you are finished with the first side - repeat operations for the other side, reposition the insulation and slide the washer back in its cavity - do not forget to reinstall the stabilizing screws in the upper washer frame
11) you've done it!
12) have a cuppa and do your second washer that hasn't failed yet - it will soon.

The video included with this part is perfect. Unplug the dishwasher, take off the front trim piece, remove the drain hose from the pump, unclip the power, press the little clip that holds the pump in while turning it counter clockwise to remove. Then just do that in the opposite order to put the new one in. Just make sure you hear it click when you twist the new one on so you know the clip has engaged. Super easy.

did need the strength of husbands hands to pop out old parts

put new hose on, very easy.

Remove dishwasher from under kitchen counter. Lay down washer on it's back using some towels or other soft material to protect floor. Disconnect plug from pump motor and to get to the hose clamp easily I had to remove diverter motor. Be careful and slide diverter motor out slowly as it needs to engage the disc when putting back together. This took most of the time since I had to orient the disc slot with the diverter motor shaft that has mating tongue that goes into slot. Install pump motor but use liquid dish soap as lubricant to get hose elbow and pump inlet to slide in mating parts. Be sure to lubricate with same on tang that fits into rubber slot. Tighten elbow hose clamp with proper pliers for job. Re-install diverter motor assembly. Inspect for any oops's and install washer back under counter. Hook back up to drain, water and electric power.

The water valve float lever was broke. So I replaced that and the water level switch. Probably didn’t have to replace switch. Very easy!!

Remove 2 screws on lower baseplate. Remove 2 screws that hold dishwasher inside cabinet( may be attached to counter top or side cabinets). Turn off water supply to dishwasher. Remove any connections such as water supply, electrical connection, or waste water line that prevent dishwasher from being pulled out about 3/4 of the way. With the dishwasher door closed, remove broken parts and replace with new parts. Pull on spring to make final connection of nylon cable. Reverse the above instructions for re-installing the machine.

I removed and reinstalled the new gasket per the video instructions, but I found the corners to be much harder to install than indicated. I finally used a large, flat, dull screwdriver to carefully push the gasket all the way in, and used my fingers to feel whether the gasket was all the way in. I figured if the gasket wasn't all the way in, I would have a leak at the bottom of the door because the top of the gasket would stick out farther than the bottom, which is exactly what the original symptoms were. Perhaps I didn't need a new gasket? There was no visible damage. Pushing in the corners of the original gasket may have fixed it, but the new gasket worked perfectly! Thanks, Part Select!!

Turn off breaker to dishwasher.
Remove lower basket.
Drain any water using a wet vac.
Remove bottom cover plate. Should be 2 plastic screws using flat head screwdriver.
Should be able to reach pump. Turn counter clockwise to remove.
Disconnect plug wire on pump.
Install new pump by turning clock wise.
Reattach wire plug.
Run a wash cycle with empty dishwasher and check for leaks.
Replace cover plate.
Done.

Hardest part was pulling dishwasher away from cabinet, making sure to not disturb water and drain line. I replaced both door springs which are on the two sides and attached to the dishwasher frame towards the back. This necessiatated pulling the dishwasher about 2/3 out of cabinet. After attaching both springs to frame, replacing the balance kit was a breeze .One screw to remove and then replace with new pulley unit. Attach the supplied cord with attached fittings to spring and then around two pulleys and mounting point on frame. Done . Push dishwasher back into cabinet, reattach two screws to underside of counter. Probably did not require new springs as they seem heavy duty and were not broken upon examination but ordered them also and replaced just in case. Most problem would be with broken cord in balance link kit

VIEW THE INSTALLATION VIDEOS. They made it clear and simple...wish every company did them...

I followed the video instructions, they were very clear. Only issue is the screws have a special head. They provide a small tool for it, but it would be easier if the head was just a philips head.

First I got online to troubleshoot issue to save mysel from a service call. One of the first UTube videos, a young man said usually the main issue was the lever. He pushed down on the floater. If it didn't click, than the lever below needed to be replaced. Most important to turn off the circuit breaker before beginning the repair. I got on whirlpool.com, Part Select, ordered the lever, which was under $10. And once delivered, was able to switch out the old lever with the new replacement. Part Quote video took me through the process step by step. The lever package was marked that usually it was only 2% of the time that replacing the lever fixed the issue. Of course, I was thrilled, my dishwasher was up and running again. Thank you.

Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.