66514422N511 Kenmore Dishwasher - Instructions

removed unit from cabinet disconnected water and drain lines replaced heater very easy to do it took more time to remove unit from under counter than replace heater piece of cake..

Removing and installing the new part was fairly simple. We removed the water hose first since it is the easiest to see. We then removed the screw holding the part to the metal frame. We slid out the part out of the holder to remove the black hose and electric plug (it is like the old phone jacks). After it was completely off we plugged in the electric to the new part which was very easy since it can only go in one way. We slid the new part in place and attached the black hose. We attached the piece to the frame with the one screw and last we attached the gold (garden hose) connection. We turned on the water to look for any leaks then turned the power on and ran it through a partial rinse to be sure there were no leaks.

I had to replace the whole sliding system on the top rack. Plus the clips holding it. It snapped. I watched the video and did the steps from Steve. The rack slides better than when brand new. Whirlpool wouldn’t pick up phone but part select did. So thank you for being there so I could fix the rack and be able to use the dishwasher again.

Husband watched your repair video. Everything went well and we are very pleased.

I manually attached the track stop to the right track in the disheasher.

1. Open dishwasher door, to access the screws holding dishwasher to cabinet.... remove these screws.
2. May need to shut water off and unscrew water line and waste line (if they aren't long enough because you will need to pull dishwasher out.
3. Unplug electricity
4. Pull dishwasher all the way out... probably need to disconnect the water and waste lines
5. crescent wrench to unscrew the plastic screws in back
6. Disconnect two wires going to element
7. Replace element... reverse steps
8. Not too bad at all
9. Part Select is Awesome !!!!

First i turned off the water and the power, then removed the two screws to the access panel under the door. Then remove 1 screw to the electrical box and removed the wire nuts and pulled the cable out of the box. Then disconect the water supply which is up front, but very little room to work. I didn't have to diconnect the drain hose because it was long enough for me to pull out the machine. After removing to screws that hold the machine to the counter you can pull it out. Remove 2 wire from the terminals of the heat coil. Unscrew the plastic nuts from the washer and remove. Assemble in reverse order and check for leaks. I tested the old element as well as the new element for resistance before installing.

The dishwasher is 25 years old. Ordering the part was simple. Very good web site and user friendly. The shipment and delivery perfect. Part arrived as predicted. Tracking delivery was also perfect. Part was exactly what I needed. The only hitch was that there were no instructions for assembly, not even a drawing of the assembly to give a hint as how to assemble. Therefiore assembly took longer than it should have. However the diswasher is back in operation and I am pleased with the results.

Followed very simple instructions to easily install. The only tool needed was a flathead scredriver to pop off caps to remove old, broken rollers. New rollers simply click into place. Piease aren't cheap, but significantly less than a new dishwasher.

I used a flat blade screwdriver to compress one arm of the endcap of the slide rail to free it. I then slid up the locking slide of the old roller assembly freeing it from the upper basket,and put the new part in its place. I then put the roller back in the slide rail and replaced the endcap.

Watched YouTube first of course. Pulled off the old gasket, found the center of the new gasket and started installing the gasket from the very top and all the way down the sides. I made sure it was in tightly and smooth. No more leak, should have listened to my wife sooner!

I checked the manual to determine the code meaning for 7 blinks, it was heating issue. I ordered the part from Partselect.com. When the part came in, I googled the internet for "How to replace a dishwasher heating element". There were several options, I chose one that was a video showing a handyman go through each step. I followed the steps, with no problems, and WA-LA! Felt good (as the wife of the house) to do it myself!

Turned water off. Removed dishwasher from under the counter, replaced hose, reinstalled dishwasher under the counter.

New one snapped right into place.

I'm the maintenance supervisor at an apartment complex. While installing a new dishwasher for a tenant, I inadvertently cross-threaded the swivel connector to the fill valve. The valve was ruined and couldn't be repaired. I ordered a new valve (it was an OEM) and installed it. Simple switch out, plus the video from Parts Select showed I had done it right.