66513092N412 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lois from Great Falls, MT
- Parts Used:
- WP3400918
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
two retainers broke and the main part fell apart
pushed the new retainers in the holes and we are set to go
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from SUSANVILLE, CA
- Parts Used:
- WPW10491331
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The filter came out and pushed the arm up on the burner and melted it.
The air just unscrews with one twist and the new arm twist right back on. No tools needs. Saved me $100 service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martha from SAN DIEGO, CA
- Parts Used:
- W10872845
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Water filter needed replacing
The old filter simply unscrews and the new one screws in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from CLINTWOOD, VA
- Parts Used:
- W11175771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
clean light blinked 4 times and repeated this over and over
I took the valve off and actually hooked 110 volts to the vale and tried to blow through it and it would not let air pass through it. I replaced the the new valve in about 15 minutes and it works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryca from TULSA, OK
- Parts Used:
- WPW10653840
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Dishwasher door stopped latching properly.
Initial inspection of the issue and research suggested the door latch was malfunctioning / broken. I bought the part and expressed it home. The installation involved removing the door screws on the inside of the door, separating the front and back panels, unplugging the door latch, removing it from its niche and popping in the new one. Reverse the take apart and it was done. Very simple swap. Hardest part was juggling the two halves of the door and preventing the door for trying to close in the process as the bulk of the weight is in the outside half of the door.
The new part did not fix the issue. The door strike was the next part that could be broken / malfunctioning. I ordered that part as well and replaced it. In the process of replacing it I found that the original door strike had been installed upside down. I am guessing it was installed at just the right pitch, or maybe even bent at the manufacturing facility, so that it latched. No idea how it managed two years like that. I installed the new one correctly and the door latches perfectly. Both parts I removed from the unit I will retain if my new parts should fail in the future.
The new part did not fix the issue. The door strike was the next part that could be broken / malfunctioning. I ordered that part as well and replaced it. In the process of replacing it I found that the original door strike had been installed upside down. I am guessing it was installed at just the right pitch, or maybe even bent at the manufacturing facility, so that it latched. No idea how it managed two years like that. I installed the new one correctly and the door latches perfectly. Both parts I removed from the unit I will retain if my new parts should fail in the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from WAUKEE, IA
- Parts Used:
- WP8268961
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Friction sleeve came apart ....would not hold door in place
Pull dishwasher out a few inches. Disconnect spring from plastic connector with long nose pliers. Remove connector. Replace friction sleeve. Replace connector.Reconnect spring to plastic connector. This completes repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johanna from JOHNSON CITY, TN
- Parts Used:
- WPW10498900
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Middle spray arm would not turn
I broke it accidentally while trying to get it off and it would either not spin or fall off. I simply removed it out of the box and put it on. 2 turns to the right and I was done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from BATON ROUGE, LA
- Parts Used:
- WP8268961
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher door drops quickly to wide open position when unlatched
Rubber friction sleeves on each side of the door provide resistance to prevent the door from quickly opening when unlatched. Over time the friction sleeve may crack and fail. Two friction sleeves are required for repair. Install a new sleeve on each side of the dishwasher door near the spring connector at the bottom.
Open dishwasher door.
Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.
Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.
Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.
Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.
Repeat for right side of door.
Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.
Slide the dishwasher back to the original position under the counter top.
Insert the screws in the top brackets to secure the dishwasher.
Open dishwasher door.
Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.
Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.
Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.
Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.
Repeat for right side of door.
Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.
Slide the dishwasher back to the original position under the counter top.
Insert the screws in the top brackets to secure the dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Ann from AUSTIN, TX
- Parts Used:
- WPW10524921
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Model number issue
When we ordered the part the first time, we pulled the model number from the documentation instead of the machine. We got the wrong part the first time. The people at Parts Select were very knowledgeable and helpful when we called. After we pulled the model number from the machine, they sent the perfect part that popped in with no problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeffrey from HOUSTON, TX
- Parts Used:
- WPW10491331
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Poor to no cleaning lower basket
lower wash arm cracked by spinning into items hanging out of bottom of basket. part twists and snaps right in. glue did not fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from MILLBURY, MA
- Parts Used:
- W11175771
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Dishwasher wasn’t getting water.
I located the water inlet valve underneath. After moving the dishwasher out from the cabinet, I tilted it . Then I disconnected the black hose with the pliers . Using the adjustable wrench I unscrewed the water feed to the valve . I then unscrewed the valve from the frame and disconnected the wire plug by unlocking and slipping it away from the valve. To install I did all this in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ginger from DONIPHAN, NE
- Parts Used:
- WPW10491331
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
top of spray arm separated from bottom causing not to hold pressure and spin
Pulled up old spray arm and snapped new on in place. Took less than a minute and no tools. Dishwasher is like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edna from WEST MONROE, LA
- Parts Used:
- WPW10653840
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
When cycling through it would stop up to 3 times & have to be restarted.
Replaced door latch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from VAN BUREN TWP, MI
- Parts Used:
- 4317824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
none
removed and installed cords with screw driver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from DOWNS, KS
- Parts Used:
- 4317824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Someone had used the wrong type of power cord
Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!
Was this instruction helpful to you?
Thank you for voting!