66513073K217 Kenmore Dishwasher - Instructions

Something had been loaded in the dishwasher that had gone thru the basket - it hit the arm sprayer and broke it off.

Replacement sprayer was exactly the same - the partselect website has very specific identification method so you get the proper part. You must have your model number.

I watched a you tube video which was referred by part select. This was helpful.

I did not realize at first that only part of the arm sprayer had broken off. The arm sprayer broke off, but there is a base to the arm sprayer that was still attached to the dishwasher. So I could not, of course , fit the new arm with its base over the existing base because they are the same size. Once I realized this, it was a simple replacement, following the youtube instructions. You do have to press and turn counter clockwise to get the old base off, but once that was done, the new sprayer arm, which arrived attached to the base, easily fit, and press hard to turn it clockwise to reattach it..

It has worked perfectly. It is a hard turn to get the arm sprayer off or on, which is good so it doesn't come loose during washing, but when replacing it, you aren't sure of why it won't turn. It is a hard turn. Watch the you tube video.

I broke it accidentally while trying to get it off and it would either not spin or fall off. I simply removed it out of the box and put it on. 2 turns to the right and I was done!

Just click in, you can basically do it with your eyes closed

The new roller assembly just snaps in place. You have to remove the rail end cap to slide the wheel into the rail. I just used a steak knife to push in the retainer so I could slide it up and out. Slide the new wheel in the track and snap the rail end cap back in place. The whole thing took maybe 5 min. Part and shipping was about $25. Problem solved. I’m sure a repair guy would have charged $150. Simple fix. Now I know where to get parts. Thanks guys!

lower wash arm cracked by spinning into items hanging out of bottom of basket. part twists and snaps right in. glue did not fix.

When we ordered the part the first time, we pulled the model number from the documentation instead of the machine. We got the wrong part the first time. The people at Parts Select were very knowledgeable and helpful when we called. After we pulled the model number from the machine, they sent the perfect part that popped in with no problems.

After reading customer notes regarding the same problem I was having I ordered A new Heater Element & a High Limit Thermostat. I also ordered a Heating Element Nut and Rubber Washer in case I needed them. It took me quite some time to remove the dishwasher from under my counter. Once the unit was out and prepared to service it actually took only a few minutes to install the new Heater Element. I did't need the washer or extra Nut. I also decided to try the unit without replacing the thermostat. I cleared the diagnostics by pressing the "HEATED DRY, "NORMAL", "HEATED DRY", "NORMAL" buttons. After the controller reset the dishwasher was ready to run.

My husband did this. He turned the dishwasher upside-down, disconnected the wires,and unbolted the heater.He put in the new heater (bolted,wired) and tested the current. Voila!

Watched a video and seen how easy it was to repair. Just disconnect the power, water and return drain. two bolts and replace element . The difficult part was removing and replacing the dishwasher...piece of cake.

Unscrewed brackets from underneath counter that hold dishwasher in place. Pulled dishwasher out of cabinet to access door hinges (approximately 8 to 12 inches). Released springs from door hinge (not necessary to remove spring from hole in dishwasher frame). Did not have to remove old sleeve because they tear and fall off. Slipped sleeve over door hinge to groove where they sit on hinge. Note: pulling hinge away from dishwasher a little. helps to complete installation.
Reinstall spring over hinge and check that door will stay a partial open. Slide dishwasher back in place and install screws from bracket to underside of counter.
My dishwasher only had two screws under counter to hold in place. Some installations have screws at sides also.

After replacing the door seal and the dishwasher still leaked a lot of water out the bottom of the door, I read posts by a couple of other DIY who said the lower spray arm can split at the seam and cause this. One post noted it is very difficult to determine if this is the problem, that you may have to take the blade of a screwdriver and try to pry the seam apart gently to see if a gap does appear with very little force being applied. If so, then just imagine what happens when that very hot water makes that plastic more flexible and then the seam opens and forces waves of water against the lower door. I could see a small seam split using that strategy and when I replaced the spray arm, my leak stopped. I don't regret replacing the door seal as it had a couple of small tears and hard water deposits all over it, so it was time to do that even though it was not the culprit for the extensive leak. The arm is SO EASY to replace, just twist the plastic nut under it and it pops right off. Put the new one on and twist the nut the other way and it secures it.

I located the water inlet valve underneath. After moving the dishwasher out from the cabinet, I tilted it . Then I disconnected the black hose with the pliers . Using the adjustable wrench I unscrewed the water feed to the valve . I then unscrewed the valve from the frame and disconnected the wire plug by unlocking and slipping it away from the valve. To install I did all this in reverse.

Removed broken part by unsnapping it and replacing it with the new part. Very, very easy.

removed and installed cords with screw driver

Snap new track stop into place. Took a few minutes to figure out top/bottom and inside/outside, but no issues