66515023K113 Kenmore Dishwasher - Instructions

I removed the lower front panel of the dishwasher to expose wheels and opened door and removed two screws holding washer to cabinet. After raising leveling feet pulled washer out to expose bnotton ow dishwasher. Removed the electrical wires form the heating element and removed screw caps holding the heaqting element in place. Removed the old element and inserted the new, then reversed process to get it back together. It was very easy to do following the instructions I received when I ordered the part.

Removed the bottom plate/cover. Unscrew top from bracket. Lucky,had just enough room to pull washer out. Only 6 in. Sleeve had broken off. Needle nose plyers to unhook spring. Slide sleeve over hinge. Hard Part///. Pull spring back into place. with door shut. good luck.

First I identified the problem by checking the plug ends of the heater coil with an ohm meter. I quickly odered the part and when it arrived a few days later, I simply pulled off the electrical connectors, unscrewed the two bolts, removed the old/broken coil, put in the new coil and tightened down the nuts snuggly.
Nothing to it. I then had to reset the error code and it is working like new.

remove 2 locks on metal roller guides. remove top basket. turn upside down on counter.remove spray arm by pryng one side in and lift out then push other side down and the out. install same as removal. line spray arm and turn clockwise til you hear a click.install basket and install locking plugs.

Removed old part and replaced with new part

thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and install new switch and reconnect the wires.

Did the repair, but needed one extra step not described in video:

I followed the directions on the PartSelect Youtube video - very helpful! I do believe the heating element was the original culprit, as it had a "burn" area about the size of a dime that caused it to almost break into two parts. Obviously a point of failure.

BUT - after replacement, it still did not solve the problem of the dishes not drying.

After much web searching, I tried the diagnostic mode on the dishwasher, and that did a hard reset of the logic board and FIXED the problem.

So in all, it required both a new heating element AND a hard reset via diagnostic mode.

I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.

Pulled dishwasher out from under the counter, removed faulty seal, installed new seal. Easy to understand directions are on web site.

Followed the easy how-to video from PS. It was as easy as changing a light bulb.

Easy to do. Less than fifteen minutes total and only tool required was a screw driver. Simply pulled out the old gasket by hand and then pressed in the new one with the screw driver. Anyone could do this.

just pulled old gasket out. New gasket took 2 attempts to fit in properly, but simple to do. Very easy to press into groove. Fit like a glove! Website drawings made choosing part very easy, thanks

I just recently purchased a new house and quickly became frustrated with the dishwasher. The top rack kept falling and interfering with the cycle and loading/unloading was an annoying pain! I investigated purchasisng a new dishwasher even though it wasn't in my budget. I decided to investigate fixing it myself. I was surprised the part was so easy to find and identify on the site. I was elated! It arrived quickly and the dishwasher was fixed in a matter of minutes. The part simply clicked into place! Instead of $500+ for a new appliance, I was saved by a $40 part (with S/H)! I love PartSelect!

It was very simple to remove the old wheel and replace with the new one. Everything snapped out of and into place so no tools were needed and it only took about 3 minutes to complete.

Something had been loaded in the dishwasher that had gone thru the basket - it hit the arm sprayer and broke it off.

Replacement sprayer was exactly the same - the partselect website has very specific identification method so you get the proper part. You must have your model number.

I watched a you tube video which was referred by part select. This was helpful.

I did not realize at first that only part of the arm sprayer had broken off. The arm sprayer broke off, but there is a base to the arm sprayer that was still attached to the dishwasher. So I could not, of course , fit the new arm with its base over the existing base because they are the same size. Once I realized this, it was a simple replacement, following the youtube instructions. You do have to press and turn counter clockwise to get the old base off, but once that was done, the new sprayer arm, which arrived attached to the base, easily fit, and press hard to turn it clockwise to reattach it..

It has worked perfectly. It is a hard turn to get the arm sprayer off or on, which is good so it doesn't come loose during washing, but when replacing it, you aren't sure of why it won't turn. It is a hard turn. Watch the you tube video.