66513292K116 Kenmore Dishwasher - Instructions

1.Check the lines for any obstruction. Gunk can easily build up. I have used the dishwasher for approx. 10 years. I do rinse/scrap dishes prior to loading.
2. Drain all remaining water.
3. Unplug the dishwasher.
4. Grab a towel and proper screw driver. Unscrew the bottom protective plate. Remove the insulation plate.
5. The drain pump is located to the bottom left. Have your towel under it. Unplug it gently. Turn counter clockwise to remove.
6. Install the new drain pump (reverse order)
7. Return the insulation plate. Screw back the bottom protective plate.
8. Plug in

saw big hole in first (main) hose - got replacement at local hardware thinking it was the only problem - it wasn't - turned on the water and noticed another leak so ordered hose from parts select - fast delivery - installed 2nd hose but still a leak so ordered grommet from parts select - again prompt delivery - installed it and voila no more leak -
also checked for rat entry points, plugged those and put down bait - bait wasn't being taken under dishwasher even tho rat reappeared so put a snap trap in back - no luck so far - teachable moment: might have been cheaper to just get another dishwasher as parts are expensive and its difficult to tell extent of damage - luckily i only needed 3 parts = $150

Very easy to repair with the replacement wheel assembly. Popped out the broken one, popped in the new one. Price was nothing compared to having an professional repair person come to the home. Glad I found you on line!

removed old gasket, installed new.
No Leaks!!
Saved the cost of a new dishwashers

all 4 wheel units needed to be replaced, popped them off and installed need wheel units in roughly 10 minutes, no tools needed.

You need to pull the unit out to get access to the spring connected to the rear leg frame. Use the everything in the kit. The rollers are upgraded and will guid the cable better.

The new lower spray arm fit right into place. All set, and I will always check to see if it is sitting properly!

Replaced Arm spray...
Turn it left and it comes off......place new spray in .. turn it right...and it's in...make sure it moves freely.......Arm wasn't turning and water was consistently hitting the front door.....I also replaced the door seal...

A Mouse friend had seen fit to chew through the original drain line. I used my Model Number, and was able to order the correct part . It arrived the next day. The job itself is fairly straight forward. You will need to access the rear of the machine. This may include shutting off, and disconnecting the water supply line. (Adjustable wrench). Mine is under the sink, on the "Hot" side. You may also need to un-plug the unit. (recommended) . A pair of (Pliers) will be needed for the spring clamp.

I followed the instructions on your recommended video; so easy! Thank you!

Watched the u tube video. Very clear! He said up front what kind of screwdriver to use and it was necessary to have that kind and size of screwdriver.

I pulled the upper rack out of the dishwasher. I then removed the broken rack clip stop on the right side and reinstalled the new replacement clip. I then put the rack back onto the rollers and voila, the upper rack no longer fell down off of the tracks!! Problem solved and the replacement clip only cost $8.95!!

Following a utube video made it easy. Removed the outer cover of the door to expose latch. Two screws remove the latch, pay attention to how it was positioned and put the new one on and then replace the panel. But first turn off the electricity to the unit at the fuse box.

Dish rack adjuster kit W10712394: I am a fully inexperienced and non-mechanical mom who needed her dishwasher during this holiday season! It took me a little longer and seemed a little harder than the description said it would - but not by much. The dishwasher is now better than it was when we bought it. Tip 1 - The original mechanism had no screws. The replacement kit does. The kit comes with a special screw that you will need in order to use a phillips screwdriver. It would have been helpful to know that before I tried to screw the screws in and stripped the first one because none of my screwdrivers fit. 2- Instructions aren't clear and photos are a little distorted (2D rather than 3D) for a novice. I wish I'd known this request for installation instructions was coming before I finished the project so I could have taken pictures. Tip - Take pictures to submit for installation instructions for others to appreciate. Would be nice to have some kind of perk to motivate people to do the work of clarifying instructions and submitting pictures. 3 - The part that locks the sliding mechanism into place is a little tricky. That step in the instructions needs some attention. I don't know how to clarify it further but other than the problem with the screws, this is the part that consumed time that an experienced dishwasher repair person might have breezed through.

First, this replacement kit seems to be of much better quality than the factory original. I was able to remove the old adjuster from the top rack with my hands - did break a little more in the process, but as this was destined for the garbage anyway, I wasn't delicate about it. The new adjuster kit snapped together easily with clear instructions and pictures in a matter of minutes, even with a 1, 3, and 5 year old "helping." Last step requires a screwdriver. I only replaced one side, for now, and it took longer to get the old adjuster off than it did to install new. Done in under ten minutes start to finish and works perfectly!