66513039K116 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gary from WAUKEE, IA
- Parts Used:
- WP8268961
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Friction sleeve came apart ....would not hold door in place
Pull dishwasher out a few inches. Disconnect spring from plastic connector with long nose pliers. Remove connector. Replace friction sleeve. Replace connector.Reconnect spring to plastic connector. This completes repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maynard from WISDOM, MT
- Parts Used:
- WPW10348269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Would not drain water
Pulled washer out far enough to put 2x4’s under front feet. Removed front panel, I clipped wire connector and unplugged it. Pushed plastic locking lever in and twisted unit counterclockwise. Wiped inner rim and reversed above procedure to assemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from OXFORD, MI
- Parts Used:
- WPW10348269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
drain pump noisy, broken piece of glass caught in pump.
removed kick panel with screwdriver, 90 degree turn of screw. Put towel under drain pump. Disconnect drain hose by loosening spring clip with pliers to provide access to pump. released spring clip on old motor while turning counterclockwise to separate pump from drain reservoir. inspect drain reservoir from inside machine to remove any foreign objects. Installed new pump by indexing attachment flanges to notches in reservoir and turning pump clockwise until locking tab makes audible click. reattach drain hose insuring hose is contacting "stop" ribs on drain hose pipe. Run wash cycle on machine to insure there are no leaks. Re-attached kick panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johanna from JOHNSON CITY, TN
- Parts Used:
- WPW10498900
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Middle spray arm would not turn
I broke it accidentally while trying to get it off and it would either not spin or fall off. I simply removed it out of the box and put it on. 2 turns to the right and I was done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from BATON ROUGE, LA
- Parts Used:
- WP8268961
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher door drops quickly to wide open position when unlatched
Rubber friction sleeves on each side of the door provide resistance to prevent the door from quickly opening when unlatched. Over time the friction sleeve may crack and fail. Two friction sleeves are required for repair. Install a new sleeve on each side of the dishwasher door near the spring connector at the bottom.
Open dishwasher door.
Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.
Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.
Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.
Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.
Repeat for right side of door.
Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.
Slide the dishwasher back to the original position under the counter top.
Insert the screws in the top brackets to secure the dishwasher.
Open dishwasher door.
Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.
Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.
Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.
Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.
Repeat for right side of door.
Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.
Slide the dishwasher back to the original position under the counter top.
Insert the screws in the top brackets to secure the dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Ann from AUSTIN, TX
- Parts Used:
- WPW10524921
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Model number issue
When we ordered the part the first time, we pulled the model number from the documentation instead of the machine. We got the wrong part the first time. The people at Parts Select were very knowledgeable and helpful when we called. After we pulled the model number from the machine, they sent the perfect part that popped in with no problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeffrey from HOUSTON, TX
- Parts Used:
- WPW10491331
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Poor to no cleaning lower basket
lower wash arm cracked by spinning into items hanging out of bottom of basket. part twists and snaps right in. glue did not fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Hicksville, NY
- Parts Used:
- W11844992
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old dishrack was rusted and chipped
Removed old rack opened box inserted new rack. So simple sorry I waited so long to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from La Center, WA
- Parts Used:
- W11844992
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original lower dish rack was falling apart.
Took out old rack, put in new one. Part arrived on time and was an exact match to the original.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from DOWNS, KS
- Parts Used:
- 4317824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Someone had used the wrong type of power cord
Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Middletown, MD
- Parts Used:
- W11844992
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher was leaving rust spots on the dishes. The lower dishrack plastic had worn away in places leaving bare metal exposed.
Just removed the old lower dishrack and set in the new one. Nothing to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from GLADSTONE, MO
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Front Track stop missing
Snap new track stop into place. Took a few minutes to figure out top/bottom and inside/outside, but no issues
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ginger from DONIPHAN, NE
- Parts Used:
- WPW10491331
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
top of spray arm separated from bottom causing not to hold pressure and spin
Pulled up old spray arm and snapped new on in place. Took less than a minute and no tools. Dishwasher is like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from VAN BUREN TWP, MI
- Parts Used:
- 4317824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
none
removed and installed cords with screw driver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from PEMBROKE PNES, FL
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Top rail stop clip broke
Very easy to remove the broken one and just clip in the new one.
Was this instruction helpful to you?
Thank you for voting!