58715234901A Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Karen from Alachua, FL
- Parts Used:
- 5304535768
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old rack had broken tines and rust
No repair, just replaced the lower rack. Your service is awesome. I received my shipment next day. Thank you so much. I will definitely use your service again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from virginia beach, VA
- Parts Used:
- 154773201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No water to dish washer
After figuring out the problem wasn't the water inlet switch, I replaced the switch assembly for the water level float. Cut off supply water to dishwasher, removed the 2 screws holding switch assembly, and installed new switch. 15 minutes, very easy job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Hummelstown, PA
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher was leaking at the lower left side of the door.
Probably the easiest repair job that you could encounter. I removed the old gasket from the door frame. Cut the new gasket to length and pushed it into the door frame.
Water leak solved...
Water leak solved...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Clinton, OH
- Parts Used:
- 809006501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Leaking Door
Pulled out old gasket from bottom of door with needle nosed pliers and then put in new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lauren from Peabody, MA
- Parts Used:
- 5304535382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
large holes in the bottom of the basket where pieces of plastic kept breaking off
I replaced the basket. No tools necessary. New basket seems sturdier than original. Very satisfied with my purchase.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from Fort Lauderdale, FL
- Parts Used:
- 5304517203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower spray arm came off and melted against the heating element
I installed the new spray arm without any tools and it worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
Door spring had broken; door would fall open
Removed the bottom panel on the unit (2 screws hold it on) and pulled the dishwasher out about 4"--after turning off electricity to the unit. Removed the broken spring and the old linkage and replaced them with the new parts. Pushed the diswasher back into place, and replaced the bottom panel. Turned on the electricity and the diswasher door is "good as new." This is quite simple to do; just takes patience.
Was this instruction helpful to you?
Thank you for voting!
One of the springs was broken, The door would not open or close properly. There was also a leak coming from the front of the dishwasher.
I removed the dishwasher from the cabinet space (two screws) and manually replaced both springs. I replaced one spring first to see if there would be an improvement when the second new spring was installed. There was much better tension once the second new spring was added.That is why changing both springs is recommended. This was very easy.
Changing the gasket was scary because I thought the the whole door would have to be taken apart. You know nothing ever goes back together the same. I feared that I would create an even bigger leak than what I had. Taken the door apart didnt work for me, so I just pulled the old gasket by hand and pressed in the new one. I made sure that it was seated correctly. Voila no leak.
The dishwasher is running as good as new.
I ordered these parts on Friday morning. They were on my door step Monday morning,
I highly recommend ordering from this site.
Changing the gasket was scary because I thought the the whole door would have to be taken apart. You know nothing ever goes back together the same. I feared that I would create an even bigger leak than what I had. Taken the door apart didnt work for me, so I just pulled the old gasket by hand and pressed in the new one. I made sure that it was seated correctly. Voila no leak.
The dishwasher is running as good as new.
I ordered these parts on Friday morning. They were on my door step Monday morning,
I highly recommend ordering from this site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffery from Excelsior Springs, MO
- Parts Used:
- 154637401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
No water was coming into dishwasher.
Unscrewed dishwasher from cabinet and pulled out about 1 foot. Took bottom plate off of dishwasher. Undid clamp on hose of discharge of inlet water valve and removed hose. Shut off water to water inlet valve and removed. Took wiring clip off of water inlet valve. Removed 2 screws holding water inlet valve in place. Installed new water inlet valve in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grant from Fairview, TN
- Parts Used:
- 809006501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water leak right bottom corner
Fully open dishwasher door to horizontal position, remove lower dishwasher rack and relocate to another temp location, grab old lower door seal from right or left corner and pull completely out of door, lay the old bottom seal aside facing the same direction as once installed (seal has a notched side which faces the right side of door), match direction of the new seal with the old seal (match the notched side of seal to the right side of door), gently push the seal into the door starting on the right side (notched side of seal fits tightly into a receiving area inside the door), and finally push the remaining portion of the seal into door (aligning with the right side already properly seated inside dishwasher door). Close dishwasher and run water cycle to confirm leak.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shannon from baltimore, MD
- Parts Used:
- 5304517203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old spray arm had melted and wasnt spraying
I removed the old spray arm by pulling it off of the base then I pushed the new one on and made sure it was on properly then I pit the base back into the dishwasher and it was good as new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAMELA from PORT ST LUCIE, FL
- Parts Used:
- 5304535768, 5304535251
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dishwasher racks had become old and plastic coating came off.
All I had to do was take out old racks and replace with new ones. However the top rack did require taking off the part where the water runs through, it was easy though.
I would like to comment on how quickly and efficiently the parts arrived. I placed my order on a monday morning and am pleased to report by tuesday afternoon they arrived, much to my delight.
I would like to comment on how quickly and efficiently the parts arrived. I placed my order on a monday morning and am pleased to report by tuesday afternoon they arrived, much to my delight.
Was this instruction helpful to you?
Thank you for voting!
Upper spray arm kept falling during cycle
Place spray arm into receptacle. Take nut and screw on being careful not to over tighten. This will strip the spray arm and the same problem will occur. Easy fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra R. from Groveland, FL
- Parts Used:
- 5304523457
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Old hose was split
The Parts finder was the big help. After that all that was needed was to loosen the clamps and replace the old hose with the new one A piece of cake. Slide the washer back into place and replace the screws that hold it to the counter. Out and back in, 30min. top end to complet the job
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Holley, NY
- Parts Used:
- 5304535382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
silverware basket skunked
tossed the old one a replaced with a new.Hardest 10 second repair ever....It took 10 seconds had to open and close the door.
Was this instruction helpful to you?
Thank you for voting!