58714022200A Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JOHN from LA QUINTA, CA
- Parts Used:
- 5304506516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
found spray arm on the rack
found spray arm on the rack looked at the top of rack saw a nut screw the nut looked at the clip found the ears broke off easy r&r.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Wisconsin Rapids, WI
- Parts Used:
- 809006501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Door leaked water
The repair went very easy. Just opened the door , and pulled out the worn seal. Lined up the new seal and carefullly pushed new seal into place. Seal pushed in very smooth.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from CONCORD, NH
- Parts Used:
- 5304512731
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
no lights on the front of the Frigidaire dishwasher
I ordered a PS12365196 BOARD from PartSelect that arrived in 2 days, a few lights came on but still did not work, next I called back to get the PS8689162 Control Assembly, (this took another 2-3 days) this has the buttons on the front that usually light up when you set up and run the dishwasher. Still no luck so i had to try and understand this as there really isn't much more to the control of the device. Went back in, by now I can take this apart in about 5 minutes, replaced the original control board and it stared right up! Called PartSelect and a few minutes later confirmed the return of the 1st part which did not seem to work. Got to go as my email just arrived with return instructions...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Avon, IN
- Parts Used:
- 809006501
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Gasket bottom of door
Removed front of door to see how gasket was installed. removed door for proper cleaning of gasket area, removed old gasket cleaned area and installed new gasket in holder notch, reinstalled door adjusting alinement, reinstalled door front.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Freehold, NJ
- Parts Used:
- 809006501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Interior bottom door gasket seal broken
Lower the door and remove bottom dish tray. Feel with fingers the area where gasket will be pulled from (just below bottom door edge) Pull old gasket from door edge into direction of inside dishwasher. Insert new one in same orientation as old (small slit to right side). New gasket strip will seat into door bottom.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from Lafayette, LA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wheels on lower rack melted
Very, very easy. Pop off the old wheels and snap the new ones into place on the rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from TULSA, OK
- Parts Used:
- 5304517203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower arm came off and melted.
Simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from Marne, MI
- Parts Used:
- 809006501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bottem door gasket was shot and leaked
Took off front door panel with two screws. Found the part in the door. took it out and slide the new part in. My husband screwed the screws while I held the door in place. If I had known it was so easy to do I would have done it as soon as I got the part but I waited for my husbands help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from MIDDLETOWN, DE
- Parts Used:
- 154430501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door won't spring back up to close
New right away when we heard the sound, the spring broke. Easy to replace, pull dishwasher out from under countertop, usually held in place by two screws into countertop. Remove screws, pull out dishwasher. Close door, springs will now have the most slack in them. One spring located on each side. Remove spring from one side and replace with new spring to ensure proper spring placement. No actual tools needed as spring rests on a bracket attached to door and other end of spring goes through hole in bottom of dishwasher rack. open door to test for tension as there are several holes to choose from. .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonnie from Erie, PA
- Parts Used:
- 5304532235, 5304517203
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower spray arm and arm support became loose fell on the hot coil and melted.
First let me say I love this company, I have used them before and I will use them again.
Parts arrived quickly, unwrapped them, put the video
supplied by this site on my phone and the entire project was done in less than ten minutes. My dishwasher works like new. Thank you !
Parts arrived quickly, unwrapped them, put the video
supplied by this site on my phone and the entire project was done in less than ten minutes. My dishwasher works like new. Thank you !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from WOODWAY, TX
- Parts Used:
- 154701001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher leaking splash shield was cracked
Watched your video repair was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from GLEN RIDGE, NJ
- Parts Used:
- A00126401
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Drain pump had failed.
Disconnected power, water, and drain tube from dishwasher. Pulled dishwasher out and laid it on right side. It was not necessary to remove the pump motor. When disconnecting the water line, it is better to remove 3/8 line from the appliance adapter rather that the appliance adapter from the dishwasher as the nylon connection tends to strip.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from SPRING HILL, FL
- Parts Used:
- 5304523457, 5304538466
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Original hose needed replacement due to leaking holes
The replacement hose was not as long and the original and therefore did not fit into the track made for the original one. Though it was long enough to work, an additional 4 inches would have been an exact fit.
As a result, the replacement had to be duct taped to the side of the dishwasher to hold it in place. Otherwise, the new hose was of better quality that the flimsy original. All in all, I could have picked up 3 feet of rubber hose from an auto parts or hardware store cheaper and done the job just as well, if not better.
As a result, the replacement had to be duct taped to the side of the dishwasher to hold it in place. Otherwise, the new hose was of better quality that the flimsy original. All in all, I could have picked up 3 feet of rubber hose from an auto parts or hardware store cheaper and done the job just as well, if not better.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from West Bloomfield, MI
- Parts Used:
- 5304512731
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dishwaser just would not start. Indicator light were flashing.
Figuring the issue was the Control Board, I ordered one. ($90) When it came I installed it...SAME problem. So I took it out and reinstalled the old board and it WORKS. Apparently some connection was not right and just moving the conectors by taking them in and back out twice fixed the problem. And FYI, since it is an electric part it is NOT returnable once it s been installed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danise from Brentwood, TN
- Parts Used:
- 809006501
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dishwasher leaked at the bottom of the door
First I removed two screws that held the door panel on. Then I pulled out the old gasket, inserted the new one, replaced the door and screws and it was done! We tested the dishwasher and no more leaks!
Was this instruction helpful to you?
Thank you for voting!