66513272K117 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jm from OSHKOSH, WI
- Parts Used:
- WP8268961
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Friction sleeve had torn, resulting in dishwasher door 'falling' when opening.
I unscrewed the dishwasher from the counter (two screws under the countertop), and pulled it out about a foot so I could access the friction sleeve. I used a needle nosed pliers to slip a spring latch off the door. Then I slipped the new friction sleeve on and reattached the spring. Tested the door. Success! Super easy. About 5 minutes of work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Derek from ROCKFORD, MI
- Parts Used:
- WPW10348269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Dishwasher Not Draining
The video included with this part is perfect. Unplug the dishwasher, take off the front trim piece, remove the drain hose from the pump, unclip the power, press the little clip that holds the pump in while turning it counter clockwise to remove. Then just do that in the opposite order to put the new one in. Just make sure you hear it click when you twist the new one on so you know the clip has engaged. Super easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from HIGHLAND MLS, NY
- Parts Used:
- WPW10348269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher had a pool of water in it after using it.
Soak up the water in the dishwasher with an old towel. Removed the cover under the dishwasher. Found the pump and twisted it off anti clockwise. Replaced with the new pump. Run a quick cycle, to make sure it pumped out all the water. My wife has used it several times since without any issues.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from SANFORD, NC
- Parts Used:
- WPW10538166
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
I damaged the grommet when removing the recirc pump
repair went smooth for the grommet. suggest a small of vasoline to ease installation of grommet
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Sultan, WA
- Parts Used:
- W11032770
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Dishes not getting washed but water draining and filling working
Remove dishwasher from under kitchen counter. Lay down washer on it's back using some towels or other soft material to protect floor. Disconnect plug from pump motor and to get to the hose clamp easily I had to remove diverter motor. Be careful and slide diverter motor out slowly as it needs to engage the disc when putting back together. This took most of the time since I had to orient the disc slot with the diverter motor shaft that has mating tongue that goes into slot. Install pump motor but use liquid dish soap as lubricant to get hose elbow and pump inlet to slide in mating parts. Be sure to lubricate with same on tang that fits into rubber slot. Tighten elbow hose clamp with proper pliers for job. Re-install diverter motor assembly. Inspect for any oops's and install washer back under counter. Hook back up to drain, water and electric power.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Kernersville, NC
- Parts Used:
- 8269144A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
old hose possible leakage
put new hose on, very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Lebanon, CT
- Parts Used:
- W10518394, WPW10477552
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Dishwasher wouldn't work
Looked under machine, saw wire going to heater was burned off.Seal on heater failed, water leaked onto terminal, shorted and burned, ruined plastic terminal nut.Replaced heater and wire terminal, and nut, took minutes, works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from WEST WARWICK, RI
- Parts Used:
- WPW10348269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would not drain. Pump was jammed with broken glass .
Turn off breaker to dishwasher.
Remove lower basket.
Drain any water using a wet vac.
Remove bottom cover plate. Should be 2 plastic screws using flat head screwdriver.
Should be able to reach pump. Turn counter clockwise to remove.
Disconnect plug wire on pump.
Install new pump by turning clock wise.
Reattach wire plug.
Run a wash cycle with empty dishwasher and check for leaks.
Replace cover plate.
Done.
Remove lower basket.
Drain any water using a wet vac.
Remove bottom cover plate. Should be 2 plastic screws using flat head screwdriver.
Should be able to reach pump. Turn counter clockwise to remove.
Disconnect plug wire on pump.
Install new pump by turning clock wise.
Reattach wire plug.
Run a wash cycle with empty dishwasher and check for leaks.
Replace cover plate.
Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LINDA from ROSEVILLE, CA
- Parts Used:
- WP8268961
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door had no resistance when opening it
You only need to pull it out about 6 to 8 inches and you don’t need to disconnect anything to slide it on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from U SADDLE RIV, NJ
- Parts Used:
- WPW10463906, WPW10491331
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishes were not getting cleaned and water was coming out the bottom of the door
The top and bottom parts of the lower wash arm were separating. This caused water to spray out the ends of the wash arm and come out the front of the dishwasher. In addition this water was not spraying upward resulting in dishes not getting cleaned. Took me a while to figure this out but the repair was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Giorgio from Savannah, GA
- Parts Used:
- 8269144A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench set
Drain hose broken.
Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from ALTADENA, CA
- Parts Used:
- WPW10491331
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
After cleaning the filter basket & metal grill (floor of dishwasher), I neglected to secure the bottom spray arm. It came loose, landed on the heating coil, and melted.
I simply removed the melted spray arm, then set the new spray arm in place, twisted the built-in securing nut (clockwise to its stop), and it worked without any problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Milwaukee, WI
- Parts Used:
- WPW10195622
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
rack stop needed to be replaced
took out the top dishwasher rack. Pulled out the track needing repair. used a flat screwdriver to pry off the defective stop. Slid the track (without the stop) back over the rollers. Snapped in the new track stop and that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SAINT CHARLES, MO
- Parts Used:
- W10872845
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
New filter
Ordering the part was very easy. It shipped fast and delivered over 3 days. It fit perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Daleville, AL
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
The dishwasher would not dry (heat)
First I identified the problem by checking the plug ends of the heater coil with an ohm meter. I quickly odered the part and when it arrived a few days later, I simply pulled off the electrical connectors, unscrewed the two bolts, removed the old/broken coil, put in the new coil and tightened down the nuts snuggly.
Nothing to it. I then had to reset the error code and it is working like new.
Nothing to it. I then had to reset the error code and it is working like new.
Was this instruction helpful to you?
Thank you for voting!