66517159K215 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Melissa from JACKSONVILLE, FL
- Parts Used:
- WP8565925
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Stop broke
Looked at how the other was installed oh and bought 2 for when the other one fails. Great customer service!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from BELFORD, NJ
- Parts Used:
- WPW10491331
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher was leaking a lot, 1-2 cups of water
Changed the seal first, very easy, no tools needed either. Helped a little, but still leaking a lot. Changed the lower spray arm and that did it. The video I watched before changing the seal helped a lot, definitely do that first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TRACEY ANN from BRICK, NJ
- Parts Used:
- WPW10195039
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
DISHWASHER WOULD NOT FILL WITH WATER
Unscrewed bottom panel of the dishwasher and simply replaced the bad control switch with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from MCMURRAY, PA
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
snap
Just snap it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from hamilton, MI
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
bad heater in qiuet partner 2
this job is cake. worst part is removing dishwasher from cabinet. Disconnect water , drain , and power. reove mounting screws in upper door area. Pull unit out and lay it on its face. unplug two wire leads and remove big nuts. Roll unit upright and replace heater. roll unit back over and tighten nuts and plug leads back in. It really takes two minutes to replace heater once the unit is out of cabinet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from The Colony, TX
- Parts Used:
- W10518394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Heater element snapped in two.
Disconnected power,water supply and drain.Had to pull dishwasher out to access the heater element nuts. Removed broken element and replaced with new part. Repair very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONALD from EAST GREENWICH, RI
- Parts Used:
- W11752368
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Tines where falling off old rack
The dishwasher is 25 years old. Ordering the part was simple. Very good web site and user friendly. The shipment and delivery perfect. Part arrived as predicted. Tracking delivery was also perfect. Part was exactly what I needed. The only hitch was that there were no instructions for assembly, not even a drawing of the assembly to give a hint as how to assemble. Therefiore assembly took longer than it should have. However the diswasher is back in operation and I am pleased with the results.
Was this instruction helpful to you?
Thank you for voting!
My dishwasher quietpartner ii was not cleaning my dishes. It seemed it was not heating correctly that the Hi temp wash or the heated dry.
I loooked up the main problems associated with that model which is provided on the website and ended up ordering a heating element and a thermostat. I replaced both parts it took me about 30 minutes. The dishwasher is working again and my wife is very happy. Thanks guys!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Beach, ND
- Parts Used:
- WP661566
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Clean light was flashing and washer would not start
Replaced heating element and high limit thermostat. Was suppose to fix the problem but did not. Replaced the control board and works now. All of these are easy to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Delaware City, DE
- Parts Used:
- W10445975
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
hose had a hole and leaked
I pulled the dishwasher out from the countertop rolled it to the side removed old clamps and hose installed new hose in kind used different hose clamps than provided turned up right pushed back in ran a cycle while looking underneath with a flashlight and saw no leaks and dishwasher has been back in use for a week now.Chris
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Monterey, CA
- Parts Used:
- W11752368
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
just wanted to replace the upper dish rack - the pieces have been rusting through
no instructions came unfortunately, but it wasn't too difficult reverse engineering. took the upper rack out, disassembled it and put the new rack together using the old screws (since there were no screws either with the replacement rack). There are some extra parts I don't know quite what to do with - some type of additional separators, but the rack works fine without them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Fort Oaks, NC
- Parts Used:
- WP661566
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Machine would shut down during the wash cycle.
I read information on this website about the function of the high limit thermostat. I found that it was the problem by disconnecting the two wires on the thermostat and straight wiring to bypass it. This allowed the machine to work properly so I ordered the high limit thermostat. To replace the part I used a screwdriver to remove the instrument panel and replaced the high limit thermostat by disconnecting the two wires from the old thermostat and connecting the wires to the new thermostat. I then replaced the instrument panel. My machine is working properly again..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from Cookeville, TN
- Parts Used:
- W10518394
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Wrench (Adjustable)
Clean light was flashing and that was only light that worked.
We had to pull the dishwasher out the get the heating element brackets loose underneath. We had to put the new heating element in and then we had to figure out which code to program in to make it reset. the last one listed on the installation instructions was the one that worked. I think it was heated dry, normal, heated dry. It would be very helpful if the reset instructions were put in the manual by whirlpool. I am very pleased with my part that I ordered from PartSelect. It came within 2 days of placing the order.
Was this instruction helpful to you?
Thank you for voting!