66513282K118 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Violet from SALEM, IL
- Parts Used:
- WPW10498900
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
I noticed my top shelf in my dishwasher was not getting the dishes clean
I read how other people had the same problem, I checked everything that could possibly cause this. I then believed I knew what was wrong. I ordered a new arm. It was unbelievable how easy it was to replace.it. It took less time than a minute. . Turn the nut holding the arm counter clockwise to remove the arm. To replace turn the nut clockwise I now have a working dishwasher. It is not necessary to remove the dish rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert R from FOLSOM, CA
- Parts Used:
- WPW10195840, W10712394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Roller mount broke Rack Adjuster
Took half hour to take off old Adjuster just trying to figure which things pop off putting on new one side 10 minute at the most
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J Kevin from Pittsburg, CA
- Parts Used:
- W10728159
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rack tines were corroded
Took off the old wheels and placed them on the new rack - fast and easy if you watch the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from WAUKEE, IA
- Parts Used:
- WP8268961
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Friction sleeve came apart ....would not hold door in place
Pull dishwasher out a few inches. Disconnect spring from plastic connector with long nose pliers. Remove connector. Replace friction sleeve. Replace connector.Reconnect spring to plastic connector. This completes repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martha from SAN DIEGO, CA
- Parts Used:
- W10872845
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Water filter needed replacing
The old filter simply unscrews and the new one screws in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from U SADDLE RIV, NJ
- Parts Used:
- WPW10463906, WPW10491331
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishes were not getting cleaned and water was coming out the bottom of the door
The top and bottom parts of the lower wash arm were separating. This caused water to spray out the ends of the wash arm and come out the front of the dishwasher. In addition this water was not spraying upward resulting in dishes not getting cleaned. Took me a while to figure this out but the repair was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sonya from YOUNGSTOWN, OH
- Parts Used:
- WPW10195622
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
TOP RACK END CLIP BROKE OFF
PULLED BROKEN CLIP OFF AND SQUEEZED NEW ONE IN. I HAD TO USE PLIERS TO SQUEEZE TOGTHER SINCE i AM 77 YEARS OLD AND HANDS ARE NOT THAT STRONG ANY MORE. I HAD ALSO WATCHED THE INTERNET VIDEO TO MAKE SURE I COULD HANDLE THIS CORRECTLY. 10 MINUTES MAX TO UNLOAD TOP RACK AND PUT TOGETHER.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from LYMAN, ME
- Parts Used:
- WPW10463906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The old filter was warped, allowing food into the sprayer system
Replaced the strainer. This keeps the two sprayers clean/clear so they do not clog up. Dishes are cleaner now. Note : if your sprayers are clogged it is a long process to clear out the sprayers. Dishes will not be clean until your sprayers are all cleared.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from Great Falls, MT
- Parts Used:
- WP3400918
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
two retainers broke and the main part fell apart
pushed the new retainers in the holes and we are set to go
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from SUSANVILLE, CA
- Parts Used:
- WPW10491331
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The filter came out and pushed the arm up on the burner and melted it.
The air just unscrews with one twist and the new arm twist right back on. No tools needs. Saved me $100 service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dylan from RIVERSIDE, CA
- Parts Used:
- WPW10348269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher not draining on final cycle and smelled of burning
I had a common issue on many dishwashers, the final drain cycle was not draining but the pump was trying to turn. Also, the drain pipe was clean. This issue caused a burning smell, like a circuit board heating up. Half plastic smell, half electrical. I bought a replacement pump, followed the pump replacement video instructions from PartsSelect, and it was replaced in under 15 minutes without any tools.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Tucson, AZ
- Parts Used:
- WPW10327249, WPW10195039
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door leaking
Float switch right in front. Did not remove dishwasher. Used small flat screwdriver to un clip cover. Very soft and easy. Unplug and it slides out.
Same with the water inlet. Did not remove and used a screwdriver and small channel locks. Turn off water. Remove hose and remove screw. Slides out. Very easy.
Same with the water inlet. Did not remove and used a screwdriver and small channel locks. Turn off water. Remove hose and remove screw. Slides out. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from MIDDLEBORO, MA
- Parts Used:
- W10728160
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Split tine row
Removed broken tin row. Replaced with new tine row. Tokk less than 1 minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from VICKSBURG, MI
- Parts Used:
- WPW10195840
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
A plastic part on the top rack of my 2 year old dishwasher broke. Automatic dishwasher soap is corrosive and plastic parts should not be used in a dishwasher in the first place
The 1st person i had contact with wasn't any help choosing the correct part. Paid about $30.00 for the wrong part. Paid $8.00 more to ship the wrong part back for reimbursement. Meanwhile my son went to a local repair shop and got the right part for less than $40 and the repair shop installed the part on the rack for free
I was not happy with Part Select! Part Select cost me time and money and didnt get the job done
I was not happy with Part Select! Part Select cost me time and money and didnt get the job done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryca from TULSA, OK
- Parts Used:
- WPW10653840
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Dishwasher door stopped latching properly.
Initial inspection of the issue and research suggested the door latch was malfunctioning / broken. I bought the part and expressed it home. The installation involved removing the door screws on the inside of the door, separating the front and back panels, unplugging the door latch, removing it from its niche and popping in the new one. Reverse the take apart and it was done. Very simple swap. Hardest part was juggling the two halves of the door and preventing the door for trying to close in the process as the bulk of the weight is in the outside half of the door.
The new part did not fix the issue. The door strike was the next part that could be broken / malfunctioning. I ordered that part as well and replaced it. In the process of replacing it I found that the original door strike had been installed upside down. I am guessing it was installed at just the right pitch, or maybe even bent at the manufacturing facility, so that it latched. No idea how it managed two years like that. I installed the new one correctly and the door latches perfectly. Both parts I removed from the unit I will retain if my new parts should fail in the future.
The new part did not fix the issue. The door strike was the next part that could be broken / malfunctioning. I ordered that part as well and replaced it. In the process of replacing it I found that the original door strike had been installed upside down. I am guessing it was installed at just the right pitch, or maybe even bent at the manufacturing facility, so that it latched. No idea how it managed two years like that. I installed the new one correctly and the door latches perfectly. Both parts I removed from the unit I will retain if my new parts should fail in the future.
Was this instruction helpful to you?
Thank you for voting!