66513255K111 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
PartSelect Scammers
PartSelect intentionally shipped obsolete part that could not possibly fit a dishwasher. The part looked to be a rectangle door seal for a freezer/ref. You make it impossible to return the part. I find it interesting that you sent the correct install video and wrong part.
Suggestion: After you print a shipping label take a picture of the part and shipping label before it is boxed. The customer should not have to send you a picture of the wrong part and the serial number of the appliance for a refund. You did not need the serial number to ship it.
I will never use your company again William Dewberry
Suggestion: After you print a shipping label take a picture of the part and shipping label before it is boxed. The customer should not have to send you a picture of the wrong part and the serial number of the appliance for a refund. You did not need the serial number to ship it.
I will never use your company again William Dewberry
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eladio from LOGAN, OH
- Parts Used:
- WPW10538166
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Develeoped a leak on the bottom.
Pulled dishwasher out of compartment, removed all parts underneath. removed inner parts, removed pump assembly. Installed new pump assembly and grommet. Reassembled in reverse order, test ran and unit was operating normal and no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from FORT COLLINS, CO
- Parts Used:
- WPW10195622
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
glide stop on upper dish rack broken
easy - plastic snap in part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from SICKLERVILLE, NJ
- Parts Used:
- 4317824
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Intermittent power loss
Remove power source, then remove old power cord.Run new power cord through existing opening ang attach to existing power box on bottom o f dishwasher. Install electrical leads and device ground. Reinstall cabinet bottom. Check out operation by running a cycle. All ok!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from RIVERSIDE, IL
- Parts Used:
- W11175771
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
The Inlet Valve cracked from the severe cold weather we had in Chicago area.
Removing and installing the new part was fairly simple. We removed the water hose first since it is the easiest to see. We then removed the screw holding the part to the metal frame. We slid out the part out of the holder to remove the black hose and electric plug (it is like the old phone jacks). After it was completely off we plugged in the electric to the new part which was very easy since it can only go in one way. We slid the new part in place and attached the black hose. We attached the piece to the frame with the one screw and last we attached the gold (garden hose) connection. We turned on the water to look for any leaks then turned the power on and ran it through a partial rinse to be sure there were no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerard from CAMARILLO, CA
- Parts Used:
- WPW10350401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rollers wear out. This is the third set since it was new.
I removed the upper rack and unclipped the roller assembly and snapped the new ones in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from TRES PINOS, CA
- Parts Used:
- W10195416
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Two wheels on the lower rack kept falling off.
Very, Very easy - watched the Installation Video highlighted on web page and the entire process took less than 5 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from ROLLA, MO
- Parts Used:
- WP8269145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
installer from lowes di not do it right, forgot to put scew in, instead he used shims, as usuall no more installs from Lowes
followed directions, a kid could have done it,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LES from NORTH PORT, FL
- Parts Used:
- WPW10195623
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic stop on front of drawer track broke off
1. Remove the top rack
2. Take a screwdriver and pry off back plastic stop at end of track
3. Slide track off, then slide new track on
4. Take the plastic back stop originally pried off of old track and snap into new track
5. Open plastic stop at front of track
6. Replace top rack.
7. Close plastic stop at from of track
8. Good to go!
2. Take a screwdriver and pry off back plastic stop at end of track
3. Slide track off, then slide new track on
4. Take the plastic back stop originally pried off of old track and snap into new track
5. Open plastic stop at front of track
6. Replace top rack.
7. Close plastic stop at from of track
8. Good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from CANTON, MA
- Parts Used:
- W10195416
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken wheel
Easy. Just watched video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- G from BISMARCK, ND
- Parts Used:
- W10195416
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
A wheel on the lower dish rack wheel assembly broke off.
Pry the old wheel assembly and snap the new one in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from FRAMINGHAM, MA
- Parts Used:
- W10195416
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Wheel came off. Hub that held the wheel to the assembly got burned by heater.
Look at the way that 3 remaining Wheel Assemblies were attached to rack, Then pop off the offending assembly and attach the new one. Less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from CINCINNATI, OH
- Parts Used:
- WPW10195622
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rack stop clip broke
Popped the old clip out, replaced with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elette from EL CAJON, CA
- Parts Used:
- WPW10195622
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Changed out the rack adjusters and wanted new clips to complete the project
They snapped into place very easily no tools required
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DONNA from BOONEVILLE, MS
- Parts Used:
- WPW10195622
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The clip on the back upper rail broke
I used pliers to pull the old clip out and pushed the new one in. Easy as that!!
Was this instruction helpful to you?
Thank you for voting!