66513255K111 Kenmore Dishwasher - Instructions

I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.

repair went smooth for the grommet. suggest a small of vasoline to ease installation of grommet

placed sprayer arm in position and twisted it into position, about a 1/4 turn, snaps into place. total of 15 seconds!

I removed and reinstalled the new gasket per the video instructions, but I found the corners to be much harder to install than indicated. I finally used a large, flat, dull screwdriver to carefully push the gasket all the way in, and used my fingers to feel whether the gasket was all the way in. I figured if the gasket wasn't all the way in, I would have a leak at the bottom of the door because the top of the gasket would stick out farther than the bottom, which is exactly what the original symptoms were. Perhaps I didn't need a new gasket? There was no visible damage. Pushing in the corners of the original gasket may have fixed it, but the new gasket worked perfectly! Thanks, Part Select!!

put new hose on, very easy.

Remove dishwasher from under kitchen counter. Lay down washer on it's back using some towels or other soft material to protect floor. Disconnect plug from pump motor and to get to the hose clamp easily I had to remove diverter motor. Be careful and slide diverter motor out slowly as it needs to engage the disc when putting back together. This took most of the time since I had to orient the disc slot with the diverter motor shaft that has mating tongue that goes into slot. Install pump motor but use liquid dish soap as lubricant to get hose elbow and pump inlet to slide in mating parts. Be sure to lubricate with same on tang that fits into rubber slot. Tighten elbow hose clamp with proper pliers for job. Re-install diverter motor assembly. Inspect for any oops's and install washer back under counter. Hook back up to drain, water and electric power.

The water valve float lever was broke. So I replaced that and the water level switch. Probably didn’t have to replace switch. Very easy!!

Turn off breaker to dishwasher.
Remove lower basket.
Drain any water using a wet vac.
Remove bottom cover plate. Should be 2 plastic screws using flat head screwdriver.
Should be able to reach pump. Turn counter clockwise to remove.
Disconnect plug wire on pump.
Install new pump by turning clock wise.
Reattach wire plug.
Run a wash cycle with empty dishwasher and check for leaks.
Replace cover plate.
Done.

did need the strength of husbands hands to pop out old parts

Remove the mounting screws that hold the dishwasher under the counter top. Remove dust cover plates at the bottom of the machine. The machine will have to be pulled out, so turn off the water to the machine. Usually under the kitchen sink. Disconnect water supply and push it out of the way so the dishwasher can be pulled out. Pull machine out enough so you have access to the door cables and springs. The door will have to be in the closed(up) position to do the repair. Usually only one side is broken. Start with the broken side and copy the working side when installing new parts. Then repair the working side. To get the working side apart just pull on the spring and disconnect it from the cable. Do the reverse to reinstall.

The video included with this part is perfect. Unplug the dishwasher, take off the front trim piece, remove the drain hose from the pump, unclip the power, press the little clip that holds the pump in while turning it counter clockwise to remove. Then just do that in the opposite order to put the new one in. Just make sure you hear it click when you twist the new one on so you know the clip has engaged. Super easy.

All I had to do is lay the shield over the top and sides and used a couple of clips to hold in place as it was slid under the counter top. It couldn’t have been easier.We had searched everywhere for this replacement shield and parts select was the the only ones that had it. Very good service and fast delivery,

Ordering the part was very easy. It shipped fast and delivered over 3 days. It fit perfectly

Removed old part and replaced with new part

remove 2 locks on metal roller guides. remove top basket. turn upside down on counter.remove spray arm by pryng one side in and lift out then push other side down and the out. install same as removal. line spray arm and turn clockwise til you hear a click.install basket and install locking plugs.