58714002993 Kenmore Dishwasher - Instructions

took it out of the bag and snapped it in. Less than 10 seconds.

Much easier than I expected. The bottom of the door gasket simply pulled out and the new one slid back into the same spot without any issues. That gasket did not solve the problem. The unit continued to leak. We waited for the back ordered door gasket approximately 2 week to come in. Once it came in the process took about 10 minutes. The old gasket easily pulled out of it's groove around the door. That gasket was dried out and worn in several places. We fitted the new gasket in the groove, trimmed off the excess, closed the door and ran the dishwasher and had no leaks. The two gaskets definitely did the trick. This is an easy DIY for anyone and the parts were priced right!!

Removed the 4 screws that held the dishwasher in place, tilted it out, removed 2 nut screws on striker, installed new striker and put it back together. Very simple.

Thank you for stocking the parts and shipping them as promised.

I'm a stay-at-home mom of 3 kids, so I enlisted the help of my oldest son (5 years old) for this job while the 2 little ones were asleep! First we cut the power to the dishwasher, then we removed the 2 bottom screws on the stainless steel front and slid it off to expose the back of the dispenser. We removed the red and white wires from the left side of the dispenser, took out the 6 screws holding the dispenser in place, put in the new dispenser, hooked up the red and white wires (in the right order), and flipped the breaker back on! We ran a cycle to make sure it worked, and it did!! My husband was thrilled! He thought for sure we needed a new dishwasher! :o) Thank you, PartSelect!

DO NOT BE TEMPTED TO REMOVE THE INNER DOOR SCREWS!!!!! I was and added about 10 minutes to a repair that should take less than 5. The lower door gasket just pulls out the bottom of the door. No tools required, just pull it out. The new one just pushes in, no click or anything, just make sure it bottoms into the groove.

I just popped on a new Arm. So easy. The amazing thing was how fast I had the part and how easy it was to find on Partselect.com. I ordered the part Monday and had it Tuesday. I was stunned and the tenant was impressed.

I had to remove the dishwasher from under the counter, flip it on it's side to gain access to the discharge hose attachment point, removeit, remove the other end of the hose from the sink-side and replace the hose. The sink-end of the hose has a 'collar' that must be cut to fit the fitting on the sink.

Removing two screws on the inside of the door alows the outside panel to slide down and detach. The soap dispenser connects with six screws and two wires. Remove the dispenser through the inside of the door. Replace, reattach and reasseble in 15 minutes.

First I shut off the power to the dishwasher from the breaker panel. Then I removed the five screws holding the plastic top panel to the door (on the frigidaire, there is no need to remove the entire stainless steel door panel). I removed each of the four wires from the old latch (pulling the wires off required some "oomph") one by one and plugged them into the corresponding position on the new one. I did this so I would be sure to have them in the right place. I used a torx screwdriver to remove the two screws holding the old latch. I then replaced the old latch with the new one, replaced the top panel of the door, turned the breaker back on and everything was as good as new! The whole operation took maybe 20 minutes. It couldn't have been easier. The only surprises were how difficult it was to pull the wires off and the fact that the screws holding the latch were torx head.

In future, when I need parts, I will definitely use PartSelect. I have gotten parts from other sources, and this is the first place where, along with the part, you get all this advice from other DIY'ers. It's an absolutely brilliant idea and a lot of help.

took the door off after several failed attempts, which is easy to do - 2 scews. Then it was easier to find the channel the gasket fits into.

For all Frigidaire diswasher owners, after taking the door off, I realized it was the seal around the soap dispenser that was leaking, due to stripped screws, not the gasket. I rigged it with silicone caulk, but may have to replace that - looks easy, .

Took the dishwasher out removed the two screws and the part holding the motor in and removed the motor. Received the parts, places o'rings on the motor, which came with the kit, even though I ordered the two o'rings. Replaced the motor, installed the part that holds the motor and tightened the screws. Cut the old connector off the dishwasher and replaced it with a new connector that came with the kit. Reinstalled the dishwasher, works great. Thanks for your Site.

Removed screws and put new bottom gasket in old one just fell out.

Snapped the new one on

pulled the old part off (no tools required) and snappen on new spray arm

PartSelect provided the perfect place to order the parts I needed. Illustrated parts breakdown on PartSelect was excellent and the correct part(s) were identified and ordered with no difficulty. I would recommend PartSelect to anyone.