58716079200 Kenmore Dishwasher - Instructions

Unplugged the dishwasher and pulled it out. Tipped it down on its side. Removed the old and replaced the new. Re-installed and replugged it. Ran a test. Checked for leaks.

Remove and replace the door gasket. Removed the 6 phillips head screws holding the top panel cover. This gives access to the latch assembly. Remove the two screw holding the latch in place. I removed the four wires one at a time with needle nose pliers and plugged them on the right spade of the new latch assembly. This assures getting them in the correct position. I then mounted the latch with the two screws and installed the cover with the 6 screws. Job done, piece of cake.

It is rather easy to repair. After you remove the screws that secure the top of the dishwasher to the countertop you can slide the disherwasher out far enough to gain access to the hose. The hose pulls off after you slide the spring clips down the hose far enough so they no longer grab. Then simply reverse the order and you're done. Less than 30 minutes and you should no longer have to hand wash your dishes!

slide out dishwasher. remove 2 screws holding motor/pump assembly in. slide out motor/pump bracket. disconnect electrical connection from motor. pull motor/pump assembly out. install new 'O' rings on new motor/pump assembly. (lube with liquid soap). install assembly. slide in motor clamp and install 2 screws. reinstall dishwasher. run test cycle. Fixed!!

Manually took off melted parts and replaced them with the new ones.

I went to your website found part# and parts diagram and ordered parts . I picked standard shipping . That evening e-mailed me they were instock and shipped also gave tracking # thet parts were here the next day.I removed the front dec panel then the 4 nut& bolts holding door to hinges(with door in closed position).Then I removed the 2 screws holding the hinges to the frame/axle. Replaced hinges with new ones .Put screws back in frame/axle . Put 4 nut and bolts back to secure door to hinges . Then i reinstalled under counter put new wheels on lower rack . I then filled it with dishes and ran a long cycle checked for leaks THEIR WERE NONE!!! THANK GOD !! Job complete, Thanks parts direct for a well designed website and detailed pics and parts#. TIM

Intuitive repair if you are one of those people that take things apart & put them back together for kicks. Nothing fancy about this repair, as all the parts have no adjusting. Remove the 6 phillips heads screws on the inside of the dishwasher panel. The front electric panel comes off, leaving the inside exposed with the wires. Unhook 4 wires to the handle. Remove (2) star shaped screw headed screws. (The most difficult part if you don't have this bit.) New handle can only go in one way. Re-attach wires & screw panel back on. The latch required pulling the dishwasher out a couple inches from under the countertop to access the mounting screws. The dishwasher is held in place with 2 screws into the countertop/or side cabinet. Slide dishwasher out. Remove 2 screws and replace. Once again, there is only one way the latch can be installed. All is good, and easily accomplished in 5 minutes....if you have the "star" bit, which does come in a couple different sizes.

replaced with new lower rack, out with the old, in with the new! Shipping was great new part arrived in 2 days! Great service, and will use again for all parts needed in the future, and will tell everyone about this site! Thanks a bunch!

The nut was split down one side, so I first tried to sauder the nut back together. Saudering never goes well for me anyway, but I couldn't get a good enough seal around the nut to make it fit tightly. Then I had to cut off the clear plastic shield to get down in there, just before realizing you could just pull the white wire firmly and it would come loose from the nut. All I had to do then was unscrew the original nut, and screw on the new nut. Then, luckily I had mistakenly ordered an extra clear plastic shield and could replace the one I had previously cut. Dishwasher now runs like a charm!

The repair went very easy. Just opened the door , and pulled out the worn seal. Lined up the new seal and carefullly pushed new seal into place. Seal pushed in very smooth.

I turned the power off at the circuit breaker. I then took the access panel off the dishwasher at the bottom. I pulled the wire off the connector. I used a plied to remove the broken washer and replaced with new part. I put everything back in reverse order and ran the dishwasher. I than checked for leaks over two days while the machine was running and everything was fine. Thank you Parts Select for saving me $500!

I took out 6 screws, the face plate just hung down. Make sure the breaker is off. there were two screws that held the switch and handle in place took those two out. Disconnected the four wires on the microswitchs and placed them on the new handle. Put the diswasher back together. Turned breaker on and worked great. But it started to leak. This is why they give you the gasket. The new latch does not always match to the same seal o the gasket. Replaced the gasket took less them two min. Ran the dishwasher again no leaks and the handle you can use one finger to unlock.

Delivery of this part was really fast. I ordered very early on a Thursday morning and the package was at my house Friday afternoon. This was a pretty simple repair. First you take the front panel off. There is an upper panel where the controls are and a lower finished apnel. Open the door, the screws are on the inside face of the door. Put a towel on the floor so the panel doesn't drop and scratch the floor or get damaged. Unscrew the panels so you can get to the door handle, it is held in with two torx screws (star shaped head). Take the handle off and remove the wires on the door switch. Installation is the reverse, mind that you install the wires on the right leads. The handle works better than the original ever did.

pulled DW out from under counter. drained water from unit. laid DW on its side. removed 5 screws from unit 2 to remove drain motor and three to remove bracket. used adj pliers to remove spring clamp and screwdriver to remove other clamp. to install i did the reverse

Simple repair.