66517425791 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- mike from SHELTON, WA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
DOOR leaking
door gasket old the vent was pluged up full of black slime cleaned out and door stopped leaking
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Ulysses, KS
- Parts Used:
- WPW10509257
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
dish washer leaking out bottom of door
New gasket did not fix problem. Cleaned air vent cover for steam to exit. Gasket not the problem but new one looks good. thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Henderson, KY
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door leaking water.
The old gasket around the door pulled out easily but was pretty nasty. While cleaning the channel out, kept finding more gunk that had built up. I decided to go ahead and take off the Inner Door. Used Torx driver to take off the screws. Found a tremendous amount of gunk built up. Was well worth taking the extra time to clean it all out. Replaced the Inner Door and put new gasket in channel. No more leaking!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Lock Haven, PA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door seal leak
Removed seal from door with flat head screwdriver, replaced with new seal. Actually took longer to get out of the box rather than to fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Coolidge, AZ
- Parts Used:
- WP3378134
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cap was missing/lost.
Easy fix. It’s a screw on by hand piece.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RUDOLPH from NORWALK, CT
- Parts Used:
- WP3374343
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher door very heavy to lift or drop down due to broken spring.
Was very easy to replace broken spring which required each end of spring to be reconnected to bracket located on the door and frame of the dishwasher. Was able to complete without moving the entire dishwasher frame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juan E from LOS LUNAS, NM
- Parts Used:
- 4386996A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Dishwasher don't drain after cycle ends
follow the video, no problem, however, its still not draining after the cycle is finish now I don't know what to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from IONIA, MI
- Parts Used:
- W11169039
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
cut wire in center sprayer to remove plastic holder for new basket
after that every thing went very well
Was this instruction helpful to you?
Thank you for voting!
Leak at the seal
Getting the dishwasher out was easy. Getting to the impeller was easy. Getting the impeller off of the motor shaft was the difficult part. I had to use my Dremel tool with lots of cutoff wheels to cut the impeller off of the motor shaft a little piece at a time. It appeared to be rust on the motor shaft that was causing the impeller to not come off. There is not much room for the Dremel so be careful not to nick the pump housing or cut into the motor shaft. Keep the vacuum close by to clean out the plastic impeller shavings. Clean the rust off the shaft with steel wool, fine sandpaper etc. Assembly was easy once everything was cleaned up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theresa from Yardville, NJ
- Parts Used:
- WPW10254672
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed an adapter to run the appliance
Very easy,take off the old faucet screen and screw on the adapter. What I really liked was the ease of ordering the part. In less than 5 minutes I had located the part and ordered it. Less than 3 days later, I had the part. Way to go PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Althea from Vancouver, WA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaking Dishwasher
I poked the old gasket with a fork tine so I could get a grip on the old gasket as I didn't have pliars, pulled it out in less than 4 seconds, folded the new gasket in half and started center top of the slot the old gasket was in and pushed the new gasket in on each side from the top to the bottom. Very easy. I'd say it took me longer to open the package with my teeth than in doing all of the above.
Was this instruction helpful to you?
Thank you for voting!
Pump impeller went crooked, apparently both from wear and moving the unit. Would not then stay in place.
Disconnected hoses (2) from pump housing. Disconnected pump housing from motor (3 allen screws, not too acessible). Unscrew spray arm from pump housing (this is done by hand; no tools as the "nut" is about 3" diameter and made of plastic) Open up the pump casing and replace impeller and the bearings on each side. The thing that takes some time is to mop the water that comes off at almost each step. There is probably an intelligent way to drain everything first. I did not order the large seal (kind of a large rubber donut, larger than a donut) between the arm and the pump and I shoiuld have as it was difficult to keep the old one from not leaking: Since by hand you cannot tighten the large nut very hard and tools could damage or break it. Applying upward pressure on the pump while tightening did it. (The pump and motor are all mounted on flexible mounts, like the heavy hoses connecting to the pump housing, so that there are no vibration.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from TEMECULA, CA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
NEW GASKET
I USED A PLUMBER
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from CHESTERFIELD, MO
- Parts Used:
- WP3368999
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Dishwasher would not dispense soap
Both springs (8066018 and 3368999) were replaced as recommended in your troubleshooting guide, but did not resolve the problem. Finally the Dual Motor, 3374501, was replaced. During the above, the plastic face of the door fell off, which created a nuisance task before proceeding to fix the original problem. However, while replacing the motor, I realized the purpose of the two, T-shaped studs sticking out of the motor. It is absolutely necessary that these sit inside the slots which engages the sliding plastic cover, which is spring loaded, in order to engage the release of the soap dispenser door. It was truly a learning experience, but I got it done.
Was this instruction helpful to you?
Thank you for voting!