36314478790 Kenmore Dishwasher - Instructions

Unscrewed bottom of spray arm support assembly counterclockwise by hand for removal. Inserted new part and screwed it in clockwise by hand for installation. Worked perfectly. Video was helpful.

Ordered door seal and followed directions included with the seal. I did put the seal in the clothes dryer for 5 minutes prior to installation as recommended in the Parts Select video that is posted on You tube.

The repair could not have been more easy! We simply unscrewed the broken spray arm and screwed in the new one. For less than $50, we fixed it ourselves. We would have paid in excess of $350 for the repairman to fix it. We could not be more happy with this website, the videos and the fast delivery!

This was one of those wonderful repairs where anything went right.
The part arrived overnight as ordered and even though I was abit leary of it fitting, since it was described as a replacement/new design, it fit perfectly! As mentioned in another post here, draining the water out of the unit so I could tip it over to do the replacement was the hardest part!
I'm sure I saved over $100 doing it myself. Thanks PartSelect!

repair kit was complete and directions were easy to follow. my model of dishwasher disnt even require any of the adapters. really only required removing a couple of clamps and replacing everything as a single unit

after I let the unit rest on its side to expose the bottom part, I took a picture just in case for reference; I marked all electrical connections, so it would go to right place into the new unit; removed the old pump unit by loosening the rubber clamps, for the inlet and outlet; detached the support sling for the motor unit; installed the new pump unit; it fits like a charm and it was wonderful; I had some bad experiences of replacement parts from other suppliers, on many things that I fix , that won't really fit like the original, but this one fits like a charm; I made my first test run with just water with out the detergent and after one cycle I used the necessary dishwasher detergent and it works just like brand new; Thank you, PartSelect, I will be ordering any of my part needs from you. - G.V.

The replacement of the motor and pump assembly went smoothly and without difficulty however this did not fix the problem. It then appeared that the inlet water valve was not operating properly, so this part was ordered and instlled, a very simple proceedure that could be done witrhout removving fthe dishwasher from its cabinet. -- Again failure to run -- the timer assembly and electronic panel were then removed and examined. The control panel had no visible defects, so the timer assemblyand its cover was removed and examined . Uing a variable power supply the drive motor for the timer was energized and tested. As the motor ran properly the electrical switching contacts were then carfully checked, it was discovered that one contact set was heavily pitted and burned. These contacts were carefully cleaned and pollished with 1000 grit sanding paper. The actuator leaves were examined and two sets were found to be slightly out of alignment. The leaves on these sets were bent slightly to insure they were in line with the rest of the leaf serts. It was then noted that the rotating leaf('s) actuator had a home position indicated by a molded depression at one location and the motor was energized using approximately 5 volts ( a nine volt battery could also be used as a poer supply) observing prolper polarity to run the rotator until the home position was established and the actuator rods paul dropped into this depression. The assembly was then replaced in the diswasher using care to make sure that the actuation arm and spring were positioned properly weith the arrow end of the arm located in the recesss of of the rotating timer disk use care in placing the assembly and do not lose the sping which attaches to a mounting post and the arm. You may want to take a picture of the spring and arm locations when you rwmove the timer assembly to properly re-assemble all components, the repaired unit was placed back in its cabinet and a full cycle run to establish proper operation. And unit checked ok! Some of these proceedures are not for the weak of heart. I am a retired engineer who has been repairing my own equipment since graduation. .

I disconnected the power shut off water supply. I then removed the drain hoses and water supply to the old pump. I removed the ground wire and the mounting rod to the old pump. Once removed, I followed the easy illustrated diagrams and instructions that came with the replacement pump.
I mounted the new pump using the supplied hardware and reconnected suply line and drain hose. I turned water supply and power back on. Ran a test cycle before reinserting under countertop. Amazingly quiet and no leaks. Repair a success.

I would use this service again if needed for additonal home appliances.

Thank you
Mr. Buddy King

Very simple to change it, only follow the instructions that came with the part and don’t have how to do wrong

Not really difficult to do. First remove the washer from the counter and flip it over. Carefully determine the correct drawing in the instructions which matches your machine. Follow insructions and double check everything. Took about an hour - and I saved about $350.00 by fixing it myself rather than buying a new one!

I went to your site and check all the diagrams and then read the postings from others. I turned off the electrical breaker then took off the lower cover of the dishwasher. After disconnecting the water and electricial connections I was able to remove the 2 screws holding the unit in place and it came right out. I turned the unit over and was able to just remove the old part and put the new part in place. The whole job took me about one hour but I had never worked on a dishwasher before. Your site made the repair very easy to do on my own.

Installed new motor and pump kit. Very easy, except that the instructions did not give any detail on the electrical hook-up. The problem was that the electrical connections for the motor and solenoid were the same on the replacement kit, making it possible to switch them. Be sure and mark the connections from the old unit before removing them.

Turn water off and unplug unit first. I remove the 2 retaining screws under counter, pulled out dishwasher. I laid it on it's side to get to pump, loosen up Hose clamps on inlet and outlet ports on pump. You may need a towel or rags to soak up a small amount of water from hoses and old pump. Removed the two hoses on the side, note the lowest one is the drain hose. Un plug all wire connections and loosen support bracket. Removed old pump and installed new one in reverse order. I had to use the 90* adapter hose and the white adapter for my drain hose.The kit contains all adapters and it all fits perfect. Reinstalled and tested unit worked great!!!

The instructions were excellent, The repair was simple. The order process was excellent, as well as the delivertime. Part Select offers excellent bluline breakdown as well as east access to help which I did not need. Thank you Part Select for yor excellence of service.

Basically, I told my girlfriend, hey, if you are board, this box has the parts to fix the dishwasher in it. When I got home from work, I had to connect one wire, and tighten a couple of screws. The kit has great, easy to follow directions. Thanks!!