66517795790 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Donna from Hicksville, NY
- Parts Used:
- W11844992
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old dishrack was rusted and chipped
Removed old rack opened box inserted new rack. So simple sorry I waited so long to replace.
Was this instruction helpful to you?
Thank you for voting!
Water was leaking (gushing) out the door
Researched parts - 10 minutes - - - Ordered parts - 5 minutes - - - Waited for parts - 14 DAYS! - - - Installed parts - 5 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from DOWNS, KS
- Parts Used:
- 4317824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Someone had used the wrong type of power cord
Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Coolidge, AZ
- Parts Used:
- WP3378134
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cap was missing/lost.
Easy fix. It’s a screw on by hand piece.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from VAN BUREN TWP, MI
- Parts Used:
- 4317824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
none
removed and installed cords with screw driver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mike from SHELTON, WA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
DOOR leaking
door gasket old the vent was pluged up full of black slime cleaned out and door stopped leaking
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Ulysses, KS
- Parts Used:
- WPW10509257
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
dish washer leaking out bottom of door
New gasket did not fix problem. Cleaned air vent cover for steam to exit. Gasket not the problem but new one looks good. thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Lock Haven, PA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door seal leak
Removed seal from door with flat head screwdriver, replaced with new seal. Actually took longer to get out of the box rather than to fix!
Was this instruction helpful to you?
Thank you for voting!
The Nut was broken in half, wash arm worned out
I just had to unscrew the old nut and screw the new one and install the new wash arm bearing ring.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from encinitas, CA
- Parts Used:
- WP3376846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
washer arm wound rotate, bearing was worn.
required NO tools,
just unscrew the large thumb screw, and replace the washer arm bearing!
problem solved like that!
maybe a 5 min job. part was a perfect match.
just unscrew the large thumb screw, and replace the washer arm bearing!
problem solved like that!
maybe a 5 min job. part was a perfect match.
Was this instruction helpful to you?
Thank you for voting!
Bearing ring missing and retainer nut broken
I put the bearing ring on the washer arm and then screwed on the retainer nut.
Easy to order the needed parts
Easy to order the needed parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Henderson, KY
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door leaking water.
The old gasket around the door pulled out easily but was pretty nasty. While cleaning the channel out, kept finding more gunk that had built up. I decided to go ahead and take off the Inner Door. Used Torx driver to take off the screws. Found a tremendous amount of gunk built up. Was well worth taking the extra time to clean it all out. Replaced the Inner Door and put new gasket in channel. No more leaking!
Was this instruction helpful to you?
Thank you for voting!
Dishwasher Leaked
At first, I suspected the door seal was at fault. However, after reading others' repair experiences, I found the dishwasher may leak if the wash arm bearings are worn. So, I took a look at those, and indeed they were quite worn.
After receiving the parts in the mail, I called my 7 and 9 year old kids over. They were excited to open the package, and weren't too disappointed when they found it was dishwasher parts. I told them it was up to them to fix the dishwasher. As I sat on a stool, I instructed them what to do. They did a great job and now it doesn't leak any more.
After receiving the parts in the mail, I called my 7 and 9 year old kids over. They were excited to open the package, and weren't too disappointed when they found it was dishwasher parts. I told them it was up to them to fix the dishwasher. As I sat on a stool, I instructed them what to do. They did a great job and now it doesn't leak any more.
Was this instruction helpful to you?
Thank you for voting!
The washarm bearing ring was completely worn thin and the lower washarm had a greater than usual wobbling
First I removed the nut holding down the lower washarm in place. I then lifted up the lower washarm where it's held in place by the nut. I replaced the two new parts: The lower sprayarm seal that seats underneath the lower washarm and the washarm bearing ring that seats on the top of the lower washarm just underneath the nut. A schematic parts list diagram can be downloaded on the KitchenAid website. The wobbling motion of the lower washarm still seems to have the same amount of play as it had before I replaced the two parts. The lower washarm itself is in fine shape including the nut. I even attempted several other different ways to install the seal and bearing ring, yet the washarm still wobbles when I manually spin it. I called KitchenAid to find out if wobbling of the lower washarm was normal. Unfortunately, the person I spoke to didn't seem to me to knowledgable enough in this area.
Was this instruction helpful to you?
Thank you for voting!