66515625691 Kenmore Dishwasher - Instructions

So my dishwasher is 20 some years old. Woke up in the morning to smell burning plastic and the dishwasher never moving to the next part in the cycle. I thought it was the high limit, then the cycling thermostat(because cycling you'd think it was cycling wrong). Nope. It was working fine. I used a multimeter to test the high limit(ohm reading will be closed at room temp) and for the cycling(will be open at room temp, so use a multimeter with alligator clips and a lighter to trigger it to close). All of my existing parts were fine. So I went to the timer and tested with alligator clips, each part that connected during the timing cycle. Sure enough. On the rinse and pump water out part, the contact point wasnt connecting due to corrosion and a bent prong. So I rebent it and cleaned all the contact points. All you need to do on these old washers is pull out the timer and pull off the thin plastic "sheild" over the thing. Guess what. I have a working dishwasher after having done the impossible and fixed my timer. So for those who have a dish washer that won't advance, but you can hear your timer advancing with the clicks, this is your problem. Saved myself an unknown amount of money because they don't make my timer anymore.

Both springs (8066018 and 3368999) were replaced as recommended in your troubleshooting guide, but did not resolve the problem. Finally the Dual Motor, 3374501, was replaced. During the above, the plastic face of the door fell off, which created a nuisance task before proceeding to fix the original problem. However, while replacing the motor, I realized the purpose of the two, T-shaped studs sticking out of the motor. It is absolutely necessary that these sit inside the slots which engages the sliding plastic cover, which is spring loaded, in order to engage the release of the soap dispenser door. It was truly a learning experience, but I got it done.

After cleaning the filter located on top left of door(used a screw driver to pry out) and following the install gasket video problem solved.

Ordered part, recieved part package, opened package, inserted screw cap rinse aid tank cover, twisted to close. Job completed. Time required about 15 seconds from opening package. Service was excellent and accurate. Thank you.

Reassembled lower access covers using the new screws purchased from parts direct, perfect fit replacement. Hardest part remembering how they fit Dishwasher.

It took all of 30 minutes from beginning to end remove the old parts and replaced them and run a diagnostic test before I could wash dishes. The parts were exact and Parts Select has always provided the right parts, shipped fast and never disappointed me.

I searched for the 18x5x5 insulation.,ordered it from Part Select. Waited. Company sent wrong part. Called, they gave me a refund, reordered, promised 2 day free shipping. Waited more than a week, paid for 2 day shipping. Received same, wrong part. Still don't have repair done. Looking elsewhere for part.

watched a video

the plastic pin that retains the spring has a head on one end that hits a plastic stop on the door to keep it from coming out. I used a small grinder and made a flat spot on the head diameter to make it easy to slide out. This is easier than trying to pry the door off the pin at the two retaing snaps. I was conderned these pin retainer clips were brittle and would break off.
Once the pin is slid out, it is a matter to hold the new spring holes in line with the pin. rotate pin so flat side you ground is turned up, so pin will not move out that way. Tiij about an hour

Removed plastic wing-nut. install new bushing.

The door seal was easy. In less than 15 minutes I peeled the old one off and installed the new one. Also the new seal arrived in 2 days. In replacing the seal I noticed a screw laying in the bottom of the dishwasher. As I removed the lower washing arm which was real easy I noticed that the plastic bearing for the lower arm was no good. Late Thursday evening I went on line and ordered the bearing, and to my surprise it was delivered to my house on Saturday. In 15 minutes I had the bearing installed and we were back in business. I'm just amazed at how easy your web site is to use, and the promptness of the parts delivery. You guys are great.

I needed to cut 1/4inch off the panel and unscrew the side piece which held it in place....
insert the new piece and put back the 3 screws. Done!

The whole job took less than 5 minutes...no tools were needed The diagnosis was right on the money

I grabbed the lower right end of the gasket with my Leatherman Tool pliers and pulled out the old gasket.
I installed the new gasket. No cleaning was necessary.
It took less than five minutes. It now works like new.
I ordered the part with standard delivery and it was here in just a couple of days. Very easy fix.

Pulled out the old with needle nose pliers. Pushed in new door seal with fingers.