66515821692 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- RUDOLPH from NORWALK, CT
- Parts Used:
- WP3374343
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher door very heavy to lift or drop down due to broken spring.
Was very easy to replace broken spring which required each end of spring to be reconnected to bracket located on the door and frame of the dishwasher. Was able to complete without moving the entire dishwasher frame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Middletown, MD
- Parts Used:
- W10833650
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher was leaving rust spots on the dishes. The lower dishrack plastic had worn away in places leaving bare metal exposed.
Just removed the old lower dishrack and set in the new one. Nothing to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Hicksville, NY
- Parts Used:
- W10833650
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old dishrack was rusted and chipped
Removed old rack opened box inserted new rack. So simple sorry I waited so long to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from La Center, WA
- Parts Used:
- W10833650
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original lower dish rack was falling apart.
Took out old rack, put in new one. Part arrived on time and was an exact match to the original.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elmer from YORKVILLE, IL
- Parts Used:
- 675806
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
1/4 inch bolt frozen to shaft
The 1/4 inch impeller bolt to shaft would not budge with a nut driver so I had to use a ratchet to loosen it. I could not hold the drain impeller with an adjustable wrench so I had to use a vice-grip. This still did not loosen it so I used an oscillating power saw to cut away at the bottom of the drain impeller being careful to only cut so deep, I didn't want to cut into the motor shaft. Once I had cut some grooves into the drain impeller, I could break it into pieces and remove it. Upon reassembly I tightened the 1/4 inch bolt with the ratchet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from IONIA, MI
- Parts Used:
- W11169039
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
cut wire in center sprayer to remove plastic holder for new basket
after that every thing went very well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wade from New Carlisle, OH
- Parts Used:
- 3367910
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
poor water circulation
follow instructions, unscrew old part, screw in new part, worked like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Althea from Vancouver, WA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaking Dishwasher
I poked the old gasket with a fork tine so I could get a grip on the old gasket as I didn't have pliars, pulled it out in less than 4 seconds, folded the new gasket in half and started center top of the slot the old gasket was in and pushed the new gasket in on each side from the top to the bottom. Very easy. I'd say it took me longer to open the package with my teeth than in doing all of the above.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sylvia from WHITESBURG, KY
- Parts Used:
- WP3369769
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Remodeling a house and front panel on dishwasher was bent and needed replaced. I just measured panel and ordered without a model or part number. Was so lucky the panel fit perfect.
Just took old panel off and went side to side and then slide panel under front trim. Of course it was easier because the bottom door trim was off and now I have to find that replacement part. Not having any luck with that!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Enderlin, ND
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
leaking around door
After cleaning the filter located on top left of door(used a screw driver to pry out) and following the install gasket video problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnny from LEVITTOWN, PA
- Parts Used:
- WP302868
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lost Screws from lower access covers for my Dishwasher
Reassembled lower access covers using the new screws purchased from parts direct, perfect fit replacement. Hardest part remembering how they fit Dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce W from WESTERLY, RI
- Parts Used:
- WP3378134
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lost the cap to the Rinse aid container in door
Ordered part, recieved part package, opened package, inserted screw cap rinse aid tank cover, twisted to close. Job completed. Time required about 15 seconds from opening package. Service was excellent and accurate. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leo from VAIL, IA
- Parts Used:
- W10833650
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Coating was worn and rack was rusting and coming apart.
Polled old rack out, removed water cone from old rack with quarter counter clockwise turn. Install cone in new rack. Slide new rack in washer. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from HOUSTON, TX
- Parts Used:
- WP717273
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dishwasher Not Heating top rack wet dishes and heating rod looks rusted
It took all of 30 minutes from beginning to end remove the old parts and replaced them and run a diagnostic test before I could wash dishes. The parts were exact and Parts Select has always provided the right parts, shipped fast and never disappointed me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanne from FAYETTE, OH
- Parts Used:
- W10728160
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Tine on rack was rusted and needed to be replaced.
Just replaced it in the notches that held the rusted tine.
Was this instruction helpful to you?
Thank you for voting!