6651571591 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kathryn from Carol Stream, IL
- Parts Used:
- WPW10348409
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Screws on the door of the dishwasher were very loose.
Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROSE from ELVERSON, PA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water was leaking ou the door
pulled the old door seal off and pushed the new seal into place and it works great!
THANK YOU!
THANK YOU!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Beach, ND
- Parts Used:
- WP661566
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Clean light was flashing and washer would not start
Replaced heating element and high limit thermostat. Was suppose to fix the problem but did not. Replaced the control board and works now. All of these are easy to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Keithville, LA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
leak in dishwasher
This was an easy fix. My husband took out the old gasket and put the new one in. It fit perfectly and no more leak. The part got to us really quickly too and that was nice. No more hand washing the dishes! :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip D from Auburn, AL
- Parts Used:
- 4387043
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Latch had broken on detergent dispenser cover
Remove retainer that holds door color slide in front of door & then remove the slide. Remove cardboard backing, remove electric latch release, remove latch & replace with new one. Open door & slide out the cup dispenser cover pin & spring & replace with new ones. This was all straight-forward & simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from matteson, IL
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
leaking
put new seal in and it still leaked!hum
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marjorie from North Grosvenordale, CT
- Parts Used:
- WP3369769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Didn't look good with the new big panel changed.
Came home and my husband had it all done. He said it was simple and it looks bran new again. Very satisfied.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Las Vegas, NY
- Parts Used:
- 4387043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
soap door hinge broke
I took the pin and i slide it through the first hole attached the spring then sldie it through the second hole and snap the cover on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicole from Newnan, GA
- Parts Used:
- 4387043
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The previous rod holding the cup in place broke
Remove completely the old one and installed the new entire kit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from ickesburg, PA
- Parts Used:
- WP3368999
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Long spring broke that pulls soap cup open
Opened the door by using a star screwdriver. Pulled the door inside from the outside. Located the broken spring, put in new one (be very carefull to see how the insides are put together..makes life ALOT easier), and carefully put back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- craig from Columbia, TN
- Parts Used:
- 4387043
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
was just missing the door and spring
You slide the pin that holds the door in the first hole. then you slide the spring in next. The you slide the pin through the last hole. After that you gently push the door onto the pin till it snaps into place. And your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bryant from melbourne, AR
- Parts Used:
- WP3376397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dishwasher was overflowing
dropped the new float in, works like a charm
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Malcolm from Cordell, OK
- Parts Used:
- WP661566
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher not working due to a faulty high limit thermostat.
Using a Torx screwdriver, I removed the fasteners holding the control panel/latch section of the door on the dishwasher. I tested the high limit thermostat with a multimeter. Just two terminals, one being power in, the other power out. The part had what I have heard call a "high resistance open". In other words, the power was not getting from "A" to "B". Power in - not out. After cutting power to the unit, I removed the part (just pull it out of the retaining clip and pull the terminals from the part). After receiving the part...by the way, really fast delivery...I reconnected the part (it doesn't matter which wire goes where), pushed the part back into the retaining clip, replaced and fastened the control panel, then restored power to the unit. Runs like new.
Was this instruction helpful to you?
Thank you for voting!
Dishes did not dry
After attempting to change the "high limit switch" to no avail, I researched further and found that doing a reset/reboot cured the problem.The instructions for the high limit thermostat were a bit off, as there was no screw to remove, only a spring like bracket that I did not try to figure out. The work area is so tight if the dishwasher is not removed and tilted that I thought it best to look for alternatives prior to pulling it out and disconnecting power and water. So ... voila, it's fixed with a reset only. Reset is accomplished by pushing two buttons 5 times. "high Temp Scrub then Heat Dry, high temp scrub then heat dry etc, until you click them both 5 times.It will go through cycles for a few minutes, then after done, run the dishwasher as normal and test if fixed. There are a few different ways to do it depending on the model.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Bellerose Manor, NY
- Parts Used:
- WP661566
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
High limit thermosat blowes when on santi. rinse
Remove blown high limit therm.and replace with the new high limit
Was this instruction helpful to you?
Thank you for voting!