6651563591 Kenmore Dishwasher - Instructions

This was an easy fix. My husband took out the old gasket and put the new one in. It fit perfectly and no more leak. The part got to us really quickly too and that was nice. No more hand washing the dishes! :)

Remove retainer that holds door color slide in front of door & then remove the slide. Remove cardboard backing, remove electric latch release, remove latch & replace with new one. Open door & slide out the cup dispenser cover pin & spring & replace with new ones. This was all straight-forward & simple.

put new seal in and it still leaked!hum

Came home and my husband had it all done. He said it was simple and it looks bran new again. Very satisfied.

I took the pin and i slide it through the first hole attached the spring then sldie it through the second hole and snap the cover on

Remove completely the old one and installed the new entire kit.

Opened the door by using a star screwdriver. Pulled the door inside from the outside. Located the broken spring, put in new one (be very carefull to see how the insides are put together..makes life ALOT easier), and carefully put back together.

You slide the pin that holds the door in the first hole. then you slide the spring in next. The you slide the pin through the last hole. After that you gently push the door onto the pin till it snaps into place. And your done.

dropped the new float in, works like a charm

Using a Torx screwdriver, I removed the fasteners holding the control panel/latch section of the door on the dishwasher. I tested the high limit thermostat with a multimeter. Just two terminals, one being power in, the other power out. The part had what I have heard call a "high resistance open". In other words, the power was not getting from "A" to "B". Power in - not out. After cutting power to the unit, I removed the part (just pull it out of the retaining clip and pull the terminals from the part). After receiving the part...by the way, really fast delivery...I reconnected the part (it doesn't matter which wire goes where), pushed the part back into the retaining clip, replaced and fastened the control panel, then restored power to the unit. Runs like new.

After attempting to change the "high limit switch" to no avail, I researched further and found that doing a reset/reboot cured the problem.The instructions for the high limit thermostat were a bit off, as there was no screw to remove, only a spring like bracket that I did not try to figure out. The work area is so tight if the dishwasher is not removed and tilted that I thought it best to look for alternatives prior to pulling it out and disconnecting power and water. So ... voila, it's fixed with a reset only. Reset is accomplished by pushing two buttons 5 times. "high Temp Scrub then Heat Dry, high temp scrub then heat dry etc, until you click them both 5 times.It will go through cycles for a few minutes, then after done, run the dishwasher as normal and test if fixed. There are a few different ways to do it depending on the model.

screw it in then hook up the hose.

Remove blown high limit therm.and replace with the new high limit

1. Turn off the electrical switch that powers the dishwasher. 2. Open the door of the dishwasher and find the two phillips head screws that secure the top of the dishwasher to the kitchen counter. 3. Remove the screws. 4. Gently move the machine side-by-side a bit while pulling it out onto the kitchen tile (be careful, the water-supply hose, electric cord, and dishwasher drain hose may not be long enough to allow you to pull it out very far - don't break or kink the hoses). 5. Remove (pull off) the black plastic fastener located on the bottom/rear of each side of the dishwasher. 6. Remove the old surround. 7. Lay the new wrap in place and secure with the two plastic fasteners. 8. Push back into place, secure the two screws, check your hoses.

The hardest part was locating the leak. After consulting the other repair suggestions, I concluded that the gasket was a little more worn on one side than the other so I ordered the gasket. The evening before the gasket arrived (quick delivery from partselect.com) I decided to shim out the old gasket with some old door insulation. It made the door harder to close but it didn't leak any more. When the gasket arrived I replaced the old with the new. It leaked more than ever. After reading more repair instructions, I decided to take apart the door vent and check it. It was packed solid with gunk. After a good cleaning, I put everything back together. No leaks! I tried every repair listed except the door vent. Guess steam is a good gunk conduit LOL. I supposed I didn't really need the new door gasket but I can tell the door has a tighter seal now. Here's a tip to watch for. If the door doesn't leak right away after the washer starts, take the door apart and look at the vent. It can look just fine from the outside and that's deceiving. Someone else mentioned the 'leak' timing that finally got my attention and lead to the 'fix.'