6651563591 Kenmore Dishwasher - Instructions

I ORDERED THE PART THAT WAS EASY BUT WHILE THE MACHINE WAS USED FOR HOW LONG I DON'T KNOW WITH OUT THE CAP IT GOT FILLED WITH FOOD AND JUNK. FIRST THING I HAD TO DO WAS EXAMIN THE DOOR AS TO HOW I COULD CLEAN THIS THING OUT. I REMOVED 6 SCREWS THAT HELD THE DOOR TOGETHER AND PULLED EASY CAUSE I DIDN'T KNOW WHAT I WAS GETTING INTO. NO PROBLEM THERE WAS NO ELECTRIC PLUGS HOOKED TO THE DOOR. I TOOK IT OUT SIDE AND STARTED USING VINIGAR AND POURING IT INTO THE HOLE AND SHAKING THEN TRYING TO GET IT BACK OUT. WELL THERE IS ONLY ONE POSITION THAT WILL LET THE VINEGAR BACK OUT. I HAD TO HOLD IT SIDEWAYS THEN TILT FORWARD AND IT WOULD RUN OUT AND BRING SOME JUNK WITH IT. THIS WAS A TIME CONSUMING PROCESS BEING YOU COULD NOT SEE INSIDE TO KNOW HOW MUCH JUNK WAS IN THERE. JUST POUR AND DUMP. AND DON'T FOR GET TO SHAKE TO LOOSEN ANY THING LEFT INSIDE.LOL I WAS VERY PROUD OF MYSELF NOT KNOWING FOR SURE IF I FIXED IT OR NOT BUT I TOOK A SHOT I HAD. I DID SOME SCRUBBING AND DEGREASING ON THE UNDERSIDE OF THE BOTTOM OF THE DOOR BEFORE I REASSEMBLED IT. THAT WAS EASY AND I CROSSED MY FINGERS ANY WAY. I GOT OUT MY NEW PART AND THE JET DRY I BOUGHT AND STATED TO FILL THE DISPENSER AND IT TOOK HALF THE BOTTLE.YEA !!! I PUT THE CAP ON AND COULDN'T WAIT TO DO A LOAD OF DISHES. EVERY THING IS LOOKING GOOD NOW. THANK YOU PART SELECT FOR MAKING GETTING THE PARTS I NEEDED SO EASY AND SHOWING DIAGRAMS SO I HAD THE RIGHT PART. I COULDN'T HAVE DONE IT WITH OUT YOU.

Turned off water and electrical. Removed kickplate at bottom of dishwasher. Unhooked water line, electrical plug and unscrewed valve from frame, noting proper position of valve for new install. The only delay we had was removing the old water line fitting from old valve. We needed the old fitting for the new valve. We solved the problem by soaking valve in boiling hot water to help loosen the connection. Install of new valve was reverse of the removal process. My son did the work and saved me approximately $200 for a service call. I also want to say that ordering the part from your company was less expensive than if I had ordered it locally and gone to pick it up! Your website is extremely helpful, user friendly, and I am recommending it to all my friends when they need to repair an appliance. Thank you!

After turning off the water to the dishwasher, I used the adjustable wrench to remove the incoming water line. Then removed the electrical feed to the water valve. Lastly I removed the rubber hose on the outlet of the valve (after compressing the retaining clip) before removing the one screw that held the valve to the lower frame of the dishwasher. Once the new part arrived, it was simply a matter of reversing the above procedure to install the new part. Took under 15 mins.

I bought the kit because it had other parts that I thought I needed.

Pulled the old gasket out with needle nose pliers, cleaned the slot for the gasket, installed the new gasket, needed no tools. This repair took 5 min.

after that every thing went very well

Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.

Took out old rack, put in new one. Part arrived on time and was an exact match to the original.

Just removed the old lower dishrack and set in the new one. Nothing to it.

The old gasket around the door pulled out easily but was pretty nasty. While cleaning the channel out, kept finding more gunk that had built up. I decided to go ahead and take off the Inner Door. Used Torx driver to take off the screws. Found a tremendous amount of gunk built up. Was well worth taking the extra time to clean it all out. Replaced the Inner Door and put new gasket in channel. No more leaking!

Easy fix. It’s a screw on by hand piece.

Was very easy to replace broken spring which required each end of spring to be reconnected to bracket located on the door and frame of the dishwasher. Was able to complete without moving the entire dishwasher frame.

Removed seal from door with flat head screwdriver, replaced with new seal. Actually took longer to get out of the box rather than to fix!

Removed old rack opened box inserted new rack. So simple sorry I waited so long to replace.

door gasket old the vent was pluged up full of black slime cleaned out and door stopped leaking