66515765691 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rheannon from Havre, MT
- Parts Used:
- WP3369193
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
These access panels are just plastic. My son's big 10 foot stepped into it and busted the holder for the screw. This was the 2nd time we had to replace this part in 4 yrs. I was very glad to find it again.
The easiest way to change this out is to remove the access panel(like the one you purchased) and the metal brace that supports it to the bottom metal access panel. To do this, REMOVE the screws in between the door and access panel. Step 2: LOOSEN screws that connect the metal braces together. You do not need to remove them completely as the middle brace slides up. You should now have the panel and brace together in your hands. Step 3: Using a flat screw driver pry (and I mean pry!) the retainers out of the catch. At this point breaking the old plastic is a better option than bending the metal! Once removed, your ready to swap out the front cover of the panels and put'er back!! Good Luck!
Was this instruction helpful to you?
Thank you for voting!
door panels looked old/bad
Washed the edges good and clean to remove old tape that was holding the old panels. Slid in the new ones and found that the retaining strip would not work without replacing the inner strip. I didn't want to order this $53 dollar plastic strip so I squeezed a couple of rubber pieces into the bottom of the side edges to hold the top panel. Placed the retaining strip in place and used a long strip of black duct tape at this bottom edge to hold it all. It works and the new panels make the dish washer look close to new,the black duct tape hardly shows. This works good for my 10+ year old dishwasher until it is replaced with one that has a better door design.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher made a crunching, grinding sound and then stopped working.
I followed the video available on partselect.com and was easily able to follow step by step the process of removing and reinstalling a new Drain and Wash Impeller and Check Ball.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from Memphis, TN
- Parts Used:
- 4318273
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Dishwasher wouldn't run
Turned off electricity. Removed the interior door cover. Removed door switch. Replaced switches & reversed process. By the way - I am a woman & diagnosised, ordered part & fixed it myself - I have no experience in this field. THANKS for all your information on your site.
Was this instruction helpful to you?
Thank you for voting!
Replaced Door Panel Insert
All I had to do was remove old door panel and retainer and I replaced with the new.
PartSelect were great. I highly recommend you guys.
PartSelect were great. I highly recommend you guys.
Was this instruction helpful to you?
Thank you for voting!
the pin was broken
but the pin in and add the pin though the 2 tabs close door on it open it up move the springs backwards to the door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Milford, NH
- Parts Used:
- W10851031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
clips had broken on the support Support Arm
I used a pair of needle nose pliers to remove the
Upper Wash Arm Support Clip from the broken support arm. Very quick re-assemble with the new part and I was able to re-use the support clip. The upper wash sprayer unit with its new support arm easily clipped in place on the upper rack.
Upper Wash Arm Support Clip from the broken support arm. Very quick re-assemble with the new part and I was able to re-use the support clip. The upper wash sprayer unit with its new support arm easily clipped in place on the upper rack.
Was this instruction helpful to you?
Thank you for voting!
Inserting Lid Spring
Had to be careful positioning the spring without breaking the hinge pin. Requires a certain amount of patience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Murfreesboro, TN
- Parts Used:
- WP8268829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The upper spray arm was cracked where it mounted to the top rack.
Ordered a new upper spray arm from PartSelect. Shipping was fast and the correct part was recieved.
Use a hair drier to warm the prongs that mount to the upper basket. The plastic is softer and will squeeze/fit in place without snapping off the "ears".
Use a hair drier to warm the prongs that mount to the upper basket. The plastic is softer and will squeeze/fit in place without snapping off the "ears".
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luann from Springfield, MO
- Parts Used:
- WP3369769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Front panel of dishwasher was dented
Pulled off the bottom trim, slid the old panel off and put the new panel on. Then popped back on the bottom trim.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Magnolia, TX
- Parts Used:
- WP3374077
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
cracked drain hose
removed two hose clamps and old hose. slid new hose on existing fittings on dishwasher drain and disposal and tightened hose clamps. Turned it on for test run.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from harrison, AR
- Parts Used:
- 3367910
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken gasket
Just put it on by hand, works great now, saved me at least 50.00!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Thomaston, GA
- Parts Used:
- WP3368999
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
detergent dispenser would not operate
remove star screws holding inside door panel. remove plastic cover that protects latch assembly. hook one end of spring on stationary pin on inside of slider bar. Hook other end of spring on pin on slider bar. replace cover and door panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Peru, IN
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
leaking suds and water front bottom of door
Replaced door gasget took 5 minutes tops. Ran cycle and still had leak. Called local repair person. After thoroughly checking out the dishwasher and running soapless cycle determined problem to be soap build up over time. He ran a commercial cleaner through a complete pots and pan cycle. No more suds and no more leak repair complete. Did not actually need door gagset but it was super easy to change and delivery service was great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Madison Township, PA
- Parts Used:
- 675806
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
dirty dishes
Installed pump kit. Was surprised the kit seemed different( some parts changed or deleted. Instructed to discard old parts and follow with new configuration. Reassembled and tried t fin it works fine now. Thank you so much
Was this instruction helpful to you?
Thank you for voting!