6651570592 Kenmore Dishwasher - Instructions

Dishwasher Stopped then only made a humming noise. Started with the Video on your site and it was quite helpful. I had trouble holding the drain impeller with the wrench. Used a drill to bore holes around the center and then broke the outer ring off to get a good hold on the center. Then was able to remove the bolt. The rest of the repair was easy. Something had caught the chopper blade and unraveled the spring. Replaced all the parts and it is working fine now.

Ordered the drain and wash impeller/chopper kit, which I received in 2 days. Great service. I watched the video on how to install the parts and the video was very clear and made the job seem easy. And it was easy, except for getting the impeller screw out. The impeller top was very brittle and pieces kept breaking off when trying to hold it with the adjustable wrench. Robo Grips didn't work any better. The only thing that finally got that screw out was a long handled socket wrench with an extension. You need the extra leverage if the screw is really stuck. Also note that the balls are definitely in the wrong place in the video. You need to remove them when doing the repair, then drop them back into the hole in the gasket/seal cover for the impeller after it is replaced. They will sit side-by-side if installed correctly. Turns out that the crunching/grinding noise was the chopper trying to chop up one of the clips that holds the silverware basket on the bottom rack. It was in many small pieces and had ripped up and split the impeller shaft.The dishwasher is back together and running perfectly. Thank you for very clear instructions on replacing the part and the quick delivery of the product.

followed the basic instructions / diagram supplied, however the impeller was fused to the shaft. Used high speed cutter to remove old impeller and sandpaper to clean up shaft.

removed old rack and replaced with the new.

Turn off the breaker to the dishwasher - there will be water very near the motor and other electrical components. I first scooped and towelled all the water out of the bottom of the dishwasher. The drain valve can be accessed from the bottom front of the dishwasher without pulling the unit out from under the counter. There were 4 screws to remove the 2 bottom metal panels. Next use pliers to loosen and slide back the hose clamp connected to the drain. Have a towel ready and pull the drain hose off the white check valve. The check valve can then be removed by unscrewing it - you may need to use pliers. Put the new one on and everything back together.

I tried going online to get some diagnostic help and never found a site that had a step by step help plan. I then did a little reading on different sites, to eliminate and perhaps diagnose my problem I use epoxy to glue the impeller(which spun freely) to the screw and it held long enough for me to see how it worked. I surfed sites to find the least expensive drain and wash impeller kit. One site had a cheaper price but I chose Parts Select because of the shipping so the end result was the best results for me. I am not sure but the estimated time was 1.7 or 1.8 days delivery that I did not believe would happen. When I received the parts and did the repair my final time from ordering was less than a day and a half. I could not have done the job myself without the video because the parts were very different. My biggest obstacle, other than my ignorance, was some sort of chemical on the screw that would not allow me to loosen it. I used a dremel to cut the head off and then a torch to heat the stub so I could remove it. After I received the kit I saw a chemical on the screw threads so online research told me heat loosens the chemical. My dishwasher is around 25 years old,I have worked on it three times now and replacing the impeller was the most difficult task to date. Should it last and develop another problem I will go to parts select first and start my quest.

My dishwasher quit working the week before Thanksgiving, and to say the least, my wife was quite concerned. I did not know what was wrong, until I found the info on this website, including a how to repair video. I watched the repair video on the website when I ordered the parts. Other than my wash arm being different from what was shown in the video, it went exactly as shown in the video. I'm glad that the video, and the bag with the parts told me that there are fewer parts than originally were installed on the original. The parts looked like they had been redesigned a little, and were easier to assemble. Overall, I will be getting any repair parts I need for other appliance repairs in the future from here. Thank you for making this experience as easy as it was.

I ordered the parts on Fri. and they came on Sat. Thanks. I had to pull the dishwasher forward about 6". Then just put the springs on. They don't have much tension with the door closed. Easy. Thanks again.

Replacing the cup latch and dispenser cover was pretty easy. First, I removed the inside cover of the door of the dishwasher. Then I carefully removed the plastic covers/slides on the door, removed the broken cup latch and then inserted the new one. Replaced the plastic covers/slides, the reinstalled the inside cover on the dishwasher. Next, I removed the dispenser cover and installed the new one. It snaps off/on, by the way. It only looks like it slides on/off.

I looked in the bottom of the dishwasher after browsing the website regarding possible solutions. When I removed the bottom spray arm I noticed three screws missing from the pump housing. The loose pump outlet had allowed the seal to push out. Ordered-Normal shipping on the part.

I installed the opener spring in the direction it was needed to open the door then installed the pin. I placed the door in the position it goes and took a pair of pliers and squeezed the pin into the pin slot. the spring has to be forced into a tension position. I did this by sliding the spring to one side and forcing it into position, the other side is done the same way. works great

I simply looked at the remaining spring to see which notch it needed to be attached to. I went in very well using a long needle nose plier. Works great.

Used the diagram and disassembled and reassembled.Used most parts that were in kit as it also fit other models and did not need all the parts.

Performed repair as to Video shown in receipt after purchase of spring plus we used a friend who has same dishwasher and has performed the same repair recently, video was easier to follow though. All you do is push off lid with a screwdriver and pop off as per instructions on video then unlatch spring from ledge and pull off post, then just reinsert new spring in reverse order or follow video instructions either way is easy and takes about 15-20 minutes to install

This Whirlpool model has the water inlet valve located in the front left of the dishwasher. It was not necessary to remove the dishwasher from under the cabinet. Disconnect the power at the breaker box and turn off the water supply to the dishwasher. Place a towel under the Valve as there will be a small amount of drainage from the water lines and the Valve when disconnected. After removing the front plate on the bottom, I could easily access the 2 screws securing the Water Inlet Valve. Disconnect the water lines on the Inlet Valve and the power connection. . Mount the new Water Inlet Valve, re-connect the water lines and the power connection to the Valve. Turn on water supply and check for leaks. Turn on power.