66517422991 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bruce W from WESTERLY, RI
- Parts Used:
- WP3378134
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lost the cap to the Rinse aid container in door
Ordered part, recieved part package, opened package, inserted screw cap rinse aid tank cover, twisted to close. Job completed. Time required about 15 seconds from opening package. Service was excellent and accurate. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnny from LEVITTOWN, PA
- Parts Used:
- WP302868
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lost Screws from lower access covers for my Dishwasher
Reassembled lower access covers using the new screws purchased from parts direct, perfect fit replacement. Hardest part remembering how they fit Dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juan E from LOS LUNAS, NM
- Parts Used:
- 4386996A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Dishwasher don't drain after cycle ends
follow the video, no problem, however, its still not draining after the cycle is finish now I don't know what to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from Brooklyn, NY
- Parts Used:
- 8268846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer rack left forward wheel cracked
I ordered the part. Sanpped it in. Fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from CHESTERFIELD, MO
- Parts Used:
- WP3368999
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Dishwasher would not dispense soap
Both springs (8066018 and 3368999) were replaced as recommended in your troubleshooting guide, but did not resolve the problem. Finally the Dual Motor, 3374501, was replaced. During the above, the plastic face of the door fell off, which created a nuisance task before proceeding to fix the original problem. However, while replacing the motor, I realized the purpose of the two, T-shaped studs sticking out of the motor. It is absolutely necessary that these sit inside the slots which engages the sliding plastic cover, which is spring loaded, in order to engage the release of the soap dispenser door. It was truly a learning experience, but I got it done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from CLEVELAND, OH
- Parts Used:
- WP8066018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Soap door wouldn't open.
I looked online to see a video. Dad to pop lid off soap dispenser. Slide a plastic part to the left n the spring slide off. Video showed how to place prongs on spring . Then had to lift the upper part of spring to lift onto plastic part of soap dispenser. That was it.
Unfortunately it still doesn't work. I asked Ina email to your company for any suggestions, No reply.
Unfortunately it still doesn't work. I asked Ina email to your company for any suggestions, No reply.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JoAnn from EAST WINDSOR, NJ
- Parts Used:
- WP8268645
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Wheel assembly was cracked
I just snapped the old one off and snapped the new one on..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dino from WURTSBORO, NY
- Parts Used:
- WP8274220
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Water would not stop flowing into dishwasher causing it to overflow on the floor
This is a portable dishwasher.. so first I turned power off and connected water line. When I turned the water on I noticed the water would flow into the dishwasher. This is not suppose to happen. This told me it was the flow valve. I disconnected water line, turned power off and removed bottom plate, removed screw holding valve on, removed water hose and output hose and unplugged valve. Then installed new valve. Turned water on to test and water did not flow into unit until cycle started. So simple. Problem solved in 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from JACKSONVILLE, FL
- Parts Used:
- W11169039
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Upper dish rack broken tines
Swapped out the old upper dish rack with a new one. A video made the change simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Constance from Sonoma, CA
- Parts Used:
- WP3369769
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
changing a damaged door panel insert
I needed to cut 1/4inch off the panel and unscrew the side piece which held it in place....
insert the new piece and put back the 3 screws. Done!
insert the new piece and put back the 3 screws. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WALTER from DES MOINES, WA
- Parts Used:
- 8268846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken roller assemblies
Just popped off the old ones and popped on the new ones. Only thing thiat might have been helpful would have been a diagram of where the roller assemblies should be located.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Dubuque, IA
- Parts Used:
- WP8066018
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
soap dish door does not always pop open
the plastic pin that retains the spring has a head on one end that hits a plastic stop on the door to keep it from coming out. I used a small grinder and made a flat spot on the head diameter to make it easy to slide out. This is easier than trying to pry the door off the pin at the two retaing snaps. I was conderned these pin retainer clips were brittle and would break off.
Once the pin is slid out, it is a matter to hold the new spring holes in line with the pin. rotate pin so flat side you ground is turned up, so pin will not move out that way. Tiij about an hour
Once the pin is slid out, it is a matter to hold the new spring holes in line with the pin. rotate pin so flat side you ground is turned up, so pin will not move out that way. Tiij about an hour
Was this instruction helpful to you?
Thank you for voting!
slow leak at motor/pump interface
Got parts breakdown online, took pump assy apart, ordered new parts, replaced bad parts, put pump assy and dishwasher back together, piece of cake, no problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Lisbon, IA
- Parts Used:
- 4386996A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench set
pump seal and impeller
had to replace the insides of a leaky pump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from York, PA
- Parts Used:
- WP3378134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cap did not stay in the hole any longer.....was melted
Just screwed the new cap in. This PartSelect was AWESOME. So easy. Lighting fast shipping !!!!
Was this instruction helpful to you?
Thank you for voting!