58717345691 Kenmore Dishwasher - Instructions

First, I located the dishwasher switch in the circuit breaker and turned it off, so as to kill power to the dishwasher - DO NOT PROCEED WITHOUT DOING THIS FIRST. Unscrewed front panel by removing 6 screws on the inside of the door frame. Then pulled 2 white wires on left and 2 black wires on right off of bottom of latch. Then used hex wrench to remove 2 hex screws holding handle and latch to frame. Then reassembled in reverse order as I disassembled. Note that there was a video on the site when I ordered the part, and it demonstrated all the steps; however, when I received the part and went back to the site to review the video again, it was gone. I'm glad I paid close attention the first time I watched it as it was extremely helpful and showed me exactly how to complete the installation.

removed screws to loosen front door panel then removed the wire connection, then removed the broken latch with screwdriver, installed new latch in same manner, fastened front panel back with the removed screws and I was back in business, easy as pie.

I replaced this latch,but noticed that the electric terminal configuration was not identical to the old original part. There were no installation instructions furnished for installing this new part, so I had to guess that the wire terminals attached to the new part in a similar position as detached from the old part. So far the renter has not called that the dishwasher is not operating correctly.

Just pushed it onto the rod that held the old one

Watched installation video and followed directions. All went smoothly.

All you have to do power down the unit, then disconnect the power connections at the element and remove the old nuts and replace them with the new ones and tighten. Don't tighten too much, the element has a rubber seal that just needs the nut to snug it up.

Removed six philip head screws to remove upper half of the dishwasher door unit to access handle, then remove handle by remove two star screws and for wires connectors. Installed in reverse.

Note:
I was very impressed on how quick I received the part after it was ordered.

After watching the repair video, it was 'easy as pie'. I would have thought the gasket was too long and cut it off if not for the video. Thank you. Saved a great deal of money not having to have a repair person do the work. I strongly recommend watching the video.

Removed the screws holding the door panel and as the sheet said was the way the it went. Two screws holding the handle latch and replaced it and put the door back on. There was 4 wires to replace on the latch. Replaced the gasket and the job was done. All in all it was a very good experience with good instructions and very good same day shipping. A VERY GOOD EXPERIENCE.

First I removed the control panel and then removed the screw holding the handle. I then pulled the connector wires off and onto the new handle. I then screwed the new panel into place. Easy job, no mess.

Removed the front cover by unscrewing the 8 screws. Removed the latch and attached new one. Re-attached front cover, and it works fine.
The gasket was in fine shape, and I question why I had to purchase the gasket in order to get the latch. Seems crazy and an unecessary expense on my part.

Take front off about 12 screws two screws held latch on took four wires off two white two black very simple to replace.

Pulled the dishwasher out, turned it on the side to gain access to the inlet valve, removed the inlet valve. The hard part was getting the valve fitting that didn't come with the inlet valve. I had to use liqued wrench to loosen the hard water deposits to get it off. Once it was off, putting the new valve on was easy. Also of note, when I tested the old vlalve with an Ohm meeter it read 8 M ohm, not infinity. The new one only measured at about 1k ohm.

The repair was pretty straightforward. If somebody is attempting, they should make sure that screws close the bottom part of the door should be opened. You only need to open the top 4 screws.

After I received the Motor Shaft Kit I removed the spray arm tower and removed all screws, the center screw would not come out of the impeller, was stripped. Used a hammer and chisel to split the center of impeller and was able to remove. Also had to split the bottom impeller because it would not come out. All the parts that came in kit fit perfectly. Thank you Very much.