66517425792 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Ridge Manor, FL
- Parts Used:
- WP3369769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Front panel was dented badly
The bottom trim piece popped off easily and I removed the damaged panel and replaced it with the new one. I snapped on the trim piece and I was done. It took less than five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from minden, LA
- Parts Used:
- 8268846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
top shelf rollers broken
snapped the old ones off and the new ones on. took less than 10 minutes easy fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from Brooksville, FL
- Parts Used:
- WP3368999
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Soap dispenser not opening
Took inside door panel off. replaced spring that opens soap dispenser lid during cycle. Put inside panel back on. Works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from FORT FAIRFIELD, ME
- Parts Used:
- WP8274220
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench set
I Was Not Geting The Water To Run Thou My Dishwasher
I Tip The DishWasher On To Its Side So I Could See Under The Dishwasher .I New The Moter Was Working Fine. I Could Here It Runing While It Was Upright . So I Determind That It WAS The Water Inlet Valve . SO I Used A Pair Of Plires To Pull Back The Clamp On The Hot Wate Hose. I Took The Hose Off . And Then I Unscrow the Hose On The Water Inlet Valve That Takes The Water Out Of The Dishwasher.I Then Used A Small Werench To Take Off Two Small Scrows Holding the Water Inlet Valve To The Dishwasher .I Pull Out The Old Water Inlet Valve I Then Found The Modle Number And Seriel Number To My 20 Year Old Whirpool Dishwasher . I Then Went On Line Useing The Name And Numbers Found Partselect And Orderd The Right Part And Put The New Part In .It Took Me Less Than 15 mins And It Saved Me Maybe A Cupple Of Houndred Dallors..Thank You Partselect..
Was this instruction helpful to you?
Thank you for voting!
broken pin and weak spring
slid the pin into place, noting correct position of spring, backed hinge pieces with screwdriver and pressed door into place. Your video made it easier than ever. ( My 2nd time replacing the pin. ) Great repair experience.
Was this instruction helpful to you?
Thank you for voting!
The soap dispenser lid spring was broken.
I watched the video, which was very good, and did the repair. It took about 10 minutes. Most of that was watching the video. EXCELLENT VIDEO!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Cameron, NC
- Parts Used:
- WPW10254672
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
changed out kitchen sink faucet set
replaced the faucet adapter I did not save when I change out the kitchen sink faucet set
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from DeSoto, TX
- Parts Used:
- 8268846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Top dish rack detached from roller
Removed the rack end stop by pressing the clip together using hand; removed the broken roller and rack support clip by snapping away from the rack. It was literally a snap to remove and replace. Very easy to do, my 12 year son could easily replace the roller assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Little Rock, AR
- Parts Used:
- 676413
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Top of the Soap Cap Latch was broken
The top of the latch was broken on I had to push the plunger back through the mounting to get it out. ai had to pull the whole assembly apart to get the locking nut out. i remove the latch assy and took about 10 minutes to figure out how to put it back together. Changing it with the help of the video wasn't hard but confusing at times. Thanks for the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrel from rosamond, CA
- Parts Used:
- WP8066018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Lid Spring
Performed repair as to Video shown in receipt after purchase of spring plus we used a friend who has same dishwasher and has performed the same repair recently, video was easier to follow though. All you do is push off lid with a screwdriver and pop off as per instructions on video then unlatch spring from ledge and pull off post, then just reinsert new spring in reverse order or follow video instructions either way is easy and takes about 15-20 minutes to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Rehoboth, MA
- Parts Used:
- 676413
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Latch worn out
Followed vidio instructionson web site. Quick easy fix
Was this instruction helpful to you?
Thank you for voting!