58715142402 Kenmore Dishwasher - Instructions

Internet search found high limit switch as primary failure, removed dishwasher existing part looked new, no signs of wear as was expected. Second failure was the heating element, I ordered the part; At the same time I found a random youtube video, that had me check the continuity of the heater and tested good. Then the video indicated the heater relay may have one leg that has lost the solder and stops the heater element from working. I took the control panel a part and the heater relay had the same failure, one leg had a missing solder joint. Using some flux, solder and soldering iron I repaired the connection and added some addition solder to the circuit. Reassembled and the dishwasher is heating as it was before everything is working as expected!
(P.S. The heater relay failure appears to be a common problem, but the actual root cause [relay failure due to poor solder joint] is never reported back to the company, they just hear the heater element stopped working and they never fix the real issue because the customers are throwing out the dishwasher, when it could have been repaired with a simple fix. More importantly it should be something that is investigated as it may needs an engineering redesign. but can't fix what you don't know about or fail to investigate. I did purchase a new relay to replace the existing one, to be installed upon arrival).
Once again a random youtube video identifies and resolves a problem, that would have had me purchasing a new dishwasher, and maybe this is all planned engineering obsolescence.
When will get smart dishwasher that have sensors or at least codes that report the failures correctly, to make DIY repairs?

1 Removed 2 screws to remove door panel so as to access back of dispenser.
2 Unplugged 2 color-coded wires attached to dispenser
3 Removed 6 screws attaching the dispenser.

Reversed these 3 steps to install new unit.

Easy. Don't even think of calling the repairman.

fixed it

Removed the 6 screws from top section inside door. Pulled control panel from front side of door. Removed two screws holding latch assemly unit and pulled 4 wires from connection. Attached the 4 wires to new door latch assembly and screwed back into place. Replaced the control panel and attached with 6 screws. Couldn't get any easier.Great service Quick delivery.

Pulled old gasket off with small hook. Replaced new gasket by pressing in with my fingers.

I removed the two screws and then moved the dishwasher out a little bit (about 6 inches). I pushed the dishwasher toward one side to make room for me to change the spring with my hand and repeated the same procedure for the other side. After the spring change, I turned an old dishwasher to a new one.

if the wire they snap on was bent it needs to be straightend.......they just snap on. easy to install but wish they had better wheels so this problem would be solved. My 2 sons have same brand dishwashers and have same problem.

pulled out dishwasher ,left lines hooked ,started cicle .heard pump.took apart.seen problem. order new one ,works like new..

The old gasket was worn. I pulled out the old one, put in the new gasket. I trimmed the ends to fit and that was it.

Took out the two retaining screws and pulled the unit forward. Took the old door strike out and put in the new one. This site is where I go for all my appliance repair parts!!!

Pulled off the old gasket and replaced it the same way with the new one.

First of all, I got the part 24 hours after I ordered it. That in it self was a feat. Second, I followed everyone elses instructions, pulled the old gasket out with a pair of needle nose pliers, cleaned the area as good as I could, found the notch for the slot on the gasket to slide into and viola...it slid in and stayed in. No more leakage whatsoever! Thanks for all of the tips!

I removed the door panel and ran the dishwasher to determine where it was leaking. Ordered the parts. When parts arrived I removed door in order to get at the bottom door gasket, replace it, and removed the tube gasket and replaced it with new parts. The whole job was very easy for a person that's never repaired a dishwasher before. I also found that the return tube gasket at the top of the dishwasher was leaking and repaired that by making a new gasket out of a flat piece of rubber and an o-ring. All leaks have been repaired. With regards to the return tube issue, it may have only been loose and if so, I could have just tightened the return tube outlet and gotten the same results. The people at this site were excellent. Thank You

Removed the two screws that mount to count top pulled the dishwasher out to see how the spring was attached , installed the new spring and the job was done the job it took about 15 mins. to complete.

1.Removed slide out dishes baskets, removed inside plastic food screen (just to clean) and disconnected electrical plug and hot water connection under the sink. 2. Unscrewed dishwasher retaining screws from kitchen counter top and slid dishwasher out (very easy). 3. Flipped dishwasher on its front. 4. Unhooked the 2 drain hoses and electrical connectors from the old drain pump, unscrewed it (torx screws) from the drain pump retainer bracket and replaced it with the new drain pump. 5. Cleaned the water jet pump (got all the accumulated crud out from the "impellers") and reinserted it in the dish washer. 5. Turned the dishwasher upright and reattached the hot water hose (using plumbers tape) and the electrical plug. 6. Finished pushing the dishwasher back under the counter, reattached the retaining screws to the counter top, turned it on and basked in the quietness of the dishwasher.