66513402K900 Kenmore Dishwasher - Instructions

Easy fix. It’s a screw on by hand piece.

Pulled dishwasher out from counter. Took cover off and replaced door springs.

This spinner is attached to a plastic module PN WP3379369 which is held in place by two screws to the top of the dishwasher. I was able to temporarily reattach the spinner by using a hot soldering iron to melt the nylon axle that goes through the spinner. By using a very small metal washer placed on top of the spinner I was able to melt enough off the end of the nylon axle so as to keep the spinner in place and still be able to rotate. By far the most difficult part of this repair is removing the two stops that prevent the upper washer rack being removed from the machine. Doing so requires using a pair of long nosed pliers and taking note of what needs to be squeezed. Even if installing a new part the upper rack needs to be removed in order to get access to this central part.

Open the dishwasher door and remove the lower dish rack.
The spray arm nut had broken off and the spray arm was wobbly.
Removed the spray arm. The threads of the nut had broken off inside the arm. I used three 1/4 inch bolts and inserted them together inside the threaded part of nut and turned counterclockwise. The threaded section came out.
Once the new nut arrived, I replaced the spray arm in the dishwasher and screwed the new nut clockwise in the center of the arm. That's it!

The 1/4 inch impeller bolt to shaft would not budge with a nut driver so I had to use a ratchet to loosen it. I could not hold the drain impeller with an adjustable wrench so I had to use a vice-grip. This still did not loosen it so I used an oscillating power saw to cut away at the bottom of the drain impeller being careful to only cut so deep, I didn't want to cut into the motor shaft. Once I had cut some grooves into the drain impeller, I could break it into pieces and remove it. Upon reassembly I tightened the 1/4 inch bolt with the ratchet.

New gasket did not fix problem. Cleaned air vent cover for steam to exit. Gasket not the problem but new one looks good. thank you

door gasket old the vent was pluged up full of black slime cleaned out and door stopped leaking

I removed the upper dishrack easily by removing the end clips and sliding the tray out. Removal of the revolving sprayer was easy as it just clipped on to the bottom of the rack. The rack was not the rack that was ordered and I was informed that this was the correct rack for the dishwasher even though the description and picture was different that what I received. There were no instructions with the rack to explain how to attach the "flaps" that can go over lightweight dishes to keep them from flipping. Every way I tried to attach the flaps did not work. When I was able to attach one it would pop off if I raised the flap to place a dish underneath it. I finally gave up on the flaps and reinserted the rack onto the rails and put the end clips back in place. The rack works fine other than it is not the one that was described and was not the rack that I wanted.

Simple easy twist on and off replacement.

Removed spray bar by removing the plastic finger thumb screw and replace as shown by you web page. Very simple.

It was very simple, the repair took less than 5 minutes start to finish. I removed the top dish rack, took out two screws and the broken part slipped right off the water feed tube. I slipped the new upper wash assembly on the end of the tube and replaced one screw. My dishwasher is an older model and the new part only has a hole for one screw but I cannot tell any difference in stability or performance. I put the top rack back on and the dishwasher is as good as before.

Our dishwasher's top rack would pull too far out which made it hard to stay in alignment. It had lost it's track stop. I easily ordered the part from PartSelect, and it came more quickly than I expected; I clicked it in place and it runs like new. It's wonderful to deal with a company that knows the frustration of not having your appliance in good working orfer.
Thank you.
Sue M
Masdsachusetts

Husband watched your repair video. Everything went well and we are very pleased.

I manually attached the track stop to the right track in the disheasher.

I had to replace the whole sliding system on the top rack. Plus the clips holding it. It snapped. I watched the video and did the steps from Steve. The rack slides better than when brand new. Whirlpool wouldn’t pick up phone but part select did. So thank you for being there so I could fix the rack and be able to use the dishwasher again.