66513173K703 Kenmore Dishwasher - Instructions

Very easy to install the new B Metal Fuse. Removed torx head screws holding the outer door panel on the dish washer. Removed the fuse and two wires connected to the fuse. Inserted the new fuse in the holder and plugged the two wire connectors back
on. Installed the outer door panel back on, turned the breaker back and the machine powered back up. Very easy install and saved a service call. Total repair cost $24

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

open dishwasher door, use torx socket and ratchet to remove 6 screws. Pull down wash options face, find the bi-metal fuse. Used the directions in the package to replace. popped old fuse out of electrical board, Cut 2 wires, stripped said wires, attached stripped wires in housing on new part, tightened the 2 screws where new wires attach, popped new fuse in electrical board. Reattached face. Very simple and easy to do. Did not fix the problem. Had to get the electrical board that the bi-metal fuse is snapped into. Very easy for someone that has worked on vehicles or electrical things before. If no experience, then I would say it is still easy as long as you follow the directions taht comes with the part. It has pictures as well.

I shut off the power to the dishwasher, then I removed the front panel under the door. On the right side just behind the electrical box there are two wires going up to the hi-limit thermostat, (you may need a small mirror to see it), remove one screw that is holding the thermostat bracket, unplug the wires from the old thermostat and install new one. Screw bracket and thermostat back to the underside of the dishwasher, reinstall the front panel, turn on the power, done.

Pulled dishwasher out from under counter. Relaced cord with plastic hook attaching spring to door. Very easy.

Very impressed with Partselect.com. Full schematic of dishwasher made it easy to select part.

Delivered in 1 day. Fantastic. Highly recommend

First I unplugged the dishwasher.Then I removed 6 Torx screws, popped off cover, cut wires to old fuse, stripped wire, placed wires in new part, tightened screws, reassembled in reverse order, plugged unit back in and tested. WOO HOO!

I saved over $150.00 by doing it myself instead of having a repairman come out! That's 4 free fishing trips!

Disconnected dishwasher from countertop and slid out about 1.5 feet.
Removed old link.
Installed new link and reconnected to spring.
slid dishwasher back under counter.
Replaced 2 screws back to countertop.
It was really really easy.

Removed the Bi-Metal fuse and ordered a new one and recerved it two days after ordering. Replaced it and it worked.

I ordered this part after the sanitized light on my dishwasher was flashing. The dishes were no longer drying. To replace the part, my husband pulled out the dishwasher and unscrewed some nuts (accessing under the heater through the side openings). The entire repair took under 15 minutes, and works perfectly. I have to mention that the heater was shaped differently than the one it replaced, but was a perfect fit in the clips.

Turned off water supply and electricity, removed the front kick panel on the dishwasher. Disconnected the water supply line, removed the two screws above the door securing the dishwasher to the underside of the countertop. Pulled the dishwasher out from under the counter, replaced the spring and balance link for each side. I found that the new balance link kit that I purchased was better engineered that the origanal equipment.

Remove two screws at top that fasten dishwasher to cabinet. Slide dishwasher out to expose the two links that attach the door to the springs. Fit the new links to the springs and door.

Removed old seal, cleaned track, applied adhesive for new seal, seated new seal in track, closed door for 24 hours to allow adhesive to cure, then used dishwasher without difficulty. An easy repair.

I watched the instructional videos that showed how to replace the inlet fill hose/water inlet a couple of times. The repair was exactly as shown. No trouble at all.

This kit comes with the link cords and the balance wheels. I only needed the cords. I undid the set screws under the counter edge and slid the Dishwasher out from under the counter. One of the links had a broken cord and the spring had snapped to the very back of the space and was a bit hard to find. I used the good side as a guide to see how to thread the cord correctly. I did not replace the wheels since they appeared to be in good shape and looked like they might be a bit more difficult to replace than just the cord. For a second I thought I had ordered the wrong part because the new cord's attachment point at the hinge did not look exactly like the originals but the new design worked just like the original. I did need one other person to help stretch the spring and hold the door in the best position so I could attach the cord to the hinge. It's working perfectly now and I saved the wheels in case I need them later.

First, ordering parts and getting diagrams from parts select is so efficient and make tthe installation so manageable. Using installation tips off the site gives u confidence to do it.
My issue was that I could not get the dishwasher from under the counter.
I removed the kick plate and screws holding it to the counter, but it was not coming out all the way. So I had to use a coat hanger to hook the spring. I attached the nylon cord first. Then I pulled the spring taut with the hanger and it was easy to thread the cord around the pulley system. I actually attached it to the door before tensioning the spring to make it easier.
Door works great now.