66513773K604 Kenmore Dishwasher - Instructions

Removed required hardware and dishwasher from undercounter mount. Turned dishwasher on its front and removed the old motor. Installed the new motor and tested for function. Installed once test was successful.

Just removed the old seal and followed the instructions that came with the new one. Since the old one didn't have any adhesive on it ,I didn't use the adhesice on the new one. Problem solved!

put new hose on, very easy.

Turn off breaker to dishwasher.
Remove lower basket.
Drain any water using a wet vac.
Remove bottom cover plate. Should be 2 plastic screws using flat head screwdriver.
Should be able to reach pump. Turn counter clockwise to remove.
Disconnect plug wire on pump.
Install new pump by turning clock wise.
Reattach wire plug.
Run a wash cycle with empty dishwasher and check for leaks.
Replace cover plate.
Done.

Watch your video about my dishwasher symptoms. Move water tube for upper rack to the right and release lower spray arm. Remove 4 clutch head screws from filter cover and remove. Dig out 10 years of undisolved soap and reassemble.

Removed old part and replaced with new part

Removed old tine rows and replaced with the new parts. No tools were needed. Each was replaced one at a time so the old ones could serve as a model for how the new ones were inserted and attached. Not much more complicated than changing a light bulb. Parts appear to be good original equipment quality but quite pricy for these very simple pieces.

removed rack
removed one screw
removed old seal
installed new seal
installed screw

Be sure to shut off power at circuit breaker and disconnect drain and water supply. Remove the dishwasher from the cabinet, lower it on its side. Remove three electrical connections from motor to various sensors. Remove three plastic wedges that secure the motor gasket to make a tight seal. The motor pops into the body of the dishwasher for removal. The replacement motor goes in just as you took it out. It took two people to set the motor right to ensure the good seal on the gasket for re-installation. Then turn it back upright and secure it in place. Couple suggestions, be sure to have ample towels around for leakage from water and drain lines. Be sure to cover the bottom of the dishwasher during disassembly and reassembly of the wash manifold. I dropped a screw in there and it took me some time to fish it out.
All in all, it went well. Don't pay a plumber for this job. I'm a clod and if I did it, you can.

disconect water supply and drain hose, unscrew 2 screws hoding front of dishwasher to countertop, slide dischwasher out so you can tip on its door and remove 1 screw hidden behind plastic shield and pull motor out install in reverse order.

Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.

I followed an excellent video on youtube which shows how to do it step by step: Dishwasher Dispenser Assembly (part #WPW10605015) - How To Replace

Snapped the new stops on. It took about 2 minutes.

I removed the upper dishwasher rack and disassembled the middle spray arm as described in other posts. Replacement was easy. The difficult part was to figure out what was causing my dishwasher to leak. I had seen many references on line to leaks being caused by the door seal or lower vent wear. I had replaced both. Those replacements resulted in less leaking, but I still had water coming out. There were also references to leaks sometimes being caused when the lower spray arm was cracked, but mine was fine. (My dishwasher has an aluminum lower arm, so it wouldn't crack.) I discovered the middle spray arm was cracked when replacing the upper dish rack. (It was starting to rust.) Apparently, when the middle spray arm is cracked, the heavier circular water flow from it creates a wave motion (vortex) in the bottom of the dishwasher. That pushes water past the seals at the bottom of the door. Once I replaced the middle spray arm the water leak problem disappeared. As an added bonus, my glasses came out cleaner! I have never seen a post indicating that a cracked middle spray arm could lead to water leakage, so hopefully this post solves someone else's mystery problem!

Hardest part was pulling dishwasher away from cabinet, making sure to not disturb water and drain line. I replaced both door springs which are on the two sides and attached to the dishwasher frame towards the back. This necessiatated pulling the dishwasher about 2/3 out of cabinet. After attaching both springs to frame, replacing the balance kit was a breeze .One screw to remove and then replace with new pulley unit. Attach the supplied cord with attached fittings to spring and then around two pulleys and mounting point on frame. Done . Push dishwasher back into cabinet, reattach two screws to underside of counter. Probably did not require new springs as they seem heavy duty and were not broken upon examination but ordered them also and replaced just in case. Most problem would be with broken cord in balance link kit