66513929K012 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ronald from VAN BUREN TWP, MI
- Parts Used:
- 4317824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
none
removed and installed cords with screw driver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from VACAVILLE, CA
- Parts Used:
- 8193983
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Spinner kept falling off.
Followed the repair video supplied by the site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from MILLBURY, MA
- Parts Used:
- W11175771
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Dishwasher wasn’t getting water.
I located the water inlet valve underneath. After moving the dishwasher out from the cabinet, I tilted it . Then I disconnected the black hose with the pliers . Using the adjustable wrench I unscrewed the water feed to the valve . I then unscrewed the valve from the frame and disconnected the wire plug by unlocking and slipping it away from the valve. To install I did all this in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from BIRMINGHAM, MI
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Dishwasher door had lost springback
1) Pull out dishwasher from under counter. 2) Disconnect spring located at the bottom on each side of dishwasher. 3) Using socket remove pulley wheels from each side at bottom. 4) Install new pulleys on each side. 5) Wind pulley cord around both wheels and attach to one end of the spring on each side. 6) Using pliers extend other spring end to lower frame of dishwasher on each side. 7) Open and close dishwasher door to test. 8) Replacement complete
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pauline from FERGUS FALLS, MN
- Parts Used:
- 8194001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
Broken plastic piece in door balance link kit
Watch video and followed instructions. Very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from LAS VEGAS, NV
- Parts Used:
- WPW10195417
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Lower Dishrack Wheel Replacement
Simply take out the lower dishwasher rack, grab a pair of pliers and gently pry the old assembly off and snap the new assembly into place. It's very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ellen from GREENWICH, CT
- Parts Used:
- WPW10195417
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
If I can do it, you can do it.
Replacing the rear wheel assembly isn't as easy as replacing the front, which took 5 minutes. You have to align the tine row, so it takes a few minutes more. But I'm a tiny woman with long nails, and if I can do it, you can do it!
Just watch the video, follow the directions, and you can't go wrong.
Just watch the video, follow the directions, and you can't go wrong.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ted from Santa Clarita, CA
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Broken cord on door balance
Very easy. I removed the two screws on the base plate, then the two screws that attach the washer to the cabinet, and pulled the washer out of its slot. I installed the broken side and closely checked the other side and felt it didn't need repairing. I put it back together and the door works very well.
Thanks,
Ted K.
Thanks,
Ted K.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pooi from TORRANCE, CA
- Parts Used:
- WPW10195622
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Upper drawer rack stop clip broke caused one side fell off rail.
I followed the YouTube attached with PartSelect email invoice to fix it. I am very happy PartSelect sent repairing video instruction and took me less than 15 minutes to get it done. Awesome!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucille from MODESTO, CA
- Parts Used:
- W10619006
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Washer would not turn on
Watched a video and read through written directions.
Did not need to pull out the dishwasher from the cabinet.
Did not need to pull out the dishwasher from the cabinet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from sullivan, OH
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door of the dishwaher banged open
Pulled the dishwasher out and took the two door balance links off and put the new ones on and attached to the spring. It was very quick and easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerard from CAMARILLO, CA
- Parts Used:
- WPW10350401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rollers wear out. This is the third set since it was new.
I removed the upper rack and unclipped the roller assembly and snapped the new ones in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LES from NORTH PORT, FL
- Parts Used:
- WPW10195623
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic stop on front of drawer track broke off
1. Remove the top rack
2. Take a screwdriver and pry off back plastic stop at end of track
3. Slide track off, then slide new track on
4. Take the plastic back stop originally pried off of old track and snap into new track
5. Open plastic stop at front of track
6. Replace top rack.
7. Close plastic stop at from of track
8. Good to go!
2. Take a screwdriver and pry off back plastic stop at end of track
3. Slide track off, then slide new track on
4. Take the plastic back stop originally pried off of old track and snap into new track
5. Open plastic stop at front of track
6. Replace top rack.
7. Close plastic stop at from of track
8. Good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from NEENAH, WI
- Parts Used:
- WPW10195417
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
old wheel assembly broke
locate lock tab and gently press
slide off the old assembly.
align and slide the new assembly on.
the lock tab is sometimes hard to push in, if you struggle with pushing it you can either break it off the old assembly or use a small flat head screwdriver to gain leverage.
slide off the old assembly.
align and slide the new assembly on.
the lock tab is sometimes hard to push in, if you struggle with pushing it you can either break it off the old assembly or use a small flat head screwdriver to gain leverage.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Scottsdale, AZ
- Parts Used:
- WPW10082853
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A bracket was missing on the top rack of dishwasher
Easy. Part just snapped in and took all of about a minute. Now the top rack doe snot slide back and forth.
Was this instruction helpful to you?
Thank you for voting!