66513159K702 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tracy from Westerville, OH
- Parts Used:
- W10258275
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Power to dish washer, but no power to any LED's or power buttons.
Very easy to install the new B Metal Fuse. Removed torx head screws holding the outer door panel on the dish washer. Removed the fuse and two wires connected to the fuse. Inserted the new fuse in the holder and plugged the two wire connectors back
on. Installed the outer door panel back on, turned the breaker back and the machine powered back up. Very easy install and saved a service call. Total repair cost $24
on. Installed the outer door panel back on, turned the breaker back and the machine powered back up. Very easy install and saved a service call. Total repair cost $24
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- 72017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jessica from Clintwood, VA
- Parts Used:
- W10258275
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lights flashing on wash options, cancel would work but nothing else
open dishwasher door, use torx socket and ratchet to remove 6 screws. Pull down wash options face, find the bi-metal fuse. Used the directions in the package to replace. popped old fuse out of electrical board, Cut 2 wires, stripped said wires, attached stripped wires in housing on new part, tightened the 2 screws where new wires attach, popped new fuse in electrical board. Reattached face. Very simple and easy to do. Did not fix the problem. Had to get the electrical board that the bi-metal fuse is snapped into. Very easy for someone that has worked on vehicles or electrical things before. If no experience, then I would say it is still easy as long as you follow the directions taht comes with the part. It has pictures as well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from WESTMONT, IL
- Parts Used:
- W10728159
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken cheap plastic wheels lower rack
Popped out old wheel housing. Popped in replacement with a little help from a flathead screwdriver. Easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Lisbon, CT
- Parts Used:
- WP661566
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dishes wouldn't dry
I shut off the power to the dishwasher, then I removed the front panel under the door. On the right side just behind the electrical box there are two wires going up to the hi-limit thermostat, (you may need a small mirror to see it), remove one screw that is holding the thermostat bracket, unplug the wires from the old thermostat and install new one. Screw bracket and thermostat back to the underside of the dishwasher, reinstall the front panel, turn on the power, done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Galt, CA
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Plastic clasp on door spring broke
Pulled dishwasher out from under counter. Relaced cord with plastic hook attaching spring to door. Very easy.
Very impressed with Partselect.com. Full schematic of dishwasher made it easy to select part.
Delivered in 1 day. Fantastic. Highly recommend
Very impressed with Partselect.com. Full schematic of dishwasher made it easy to select part.
Delivered in 1 day. Fantastic. Highly recommend
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Ridgecrest, CA
- Parts Used:
- W10258275
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Wirlpool Dishwasher not getting power to panel. Outlet checked out fine
First I unplugged the dishwasher.Then I removed 6 Torx screws, popped off cover, cut wires to old fuse, stripped wire, placed wires in new part, tightened screws, reassembled in reverse order, plugged unit back in and tested. WOO HOO!
I saved over $150.00 by doing it myself instead of having a repairman come out! That's 4 free fishing trips!
I saved over $150.00 by doing it myself instead of having a repairman come out! That's 4 free fishing trips!
Was this instruction helpful to you?
Thank you for voting!
Door balance link connection was broken
Disconnected dishwasher from countertop and slid out about 1.5 feet.
Removed old link.
Installed new link and reconnected to spring.
slid dishwasher back under counter.
Replaced 2 screws back to countertop.
It was really really easy.
Removed old link.
Installed new link and reconnected to spring.
slid dishwasher back under counter.
Replaced 2 screws back to countertop.
It was really really easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from FERNANDINA, FL
- Parts Used:
- W10258275
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would not run
Removed the Bi-Metal fuse and ordered a new one and recerved it two days after ordering. Replaced it and it worked.
Was this instruction helpful to you?
Thank you for voting!
Door would fall when opened.
Turned off water supply and electricity, removed the front kick panel on the dishwasher. Disconnected the water supply line, removed the two screws above the door securing the dishwasher to the underside of the countertop. Pulled the dishwasher out from under the counter, replaced the spring and balance link for each side. I found that the new balance link kit that I purchased was better engineered that the origanal equipment.
Was this instruction helpful to you?
Thank you for voting!
The upper & lower rack was rusted and broken in several areas.
It was easy! First I ordered the expensive replacement parts on line. The parts arrived in one week. I was able to slide the old drawers out, slip a few parts off of the old drawers, snap them on and slide the new drawers in place!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ellen from Park City, UT
- Parts Used:
- WPW10082892
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher heater broken
I ordered this part after the sanitized light on my dishwasher was flashing. The dishes were no longer drying. To replace the part, my husband pulled out the dishwasher and unscrewed some nuts (accessing under the heater through the side openings). The entire repair took under 15 minutes, and works perfectly. I have to mention that the heater was shaped differently than the one it replaced, but was a perfect fit in the clips.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Great Falls, VA
- Parts Used:
- W10727422
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Upper Dishrack and tines rusting out
My KitchenAid dishwasher's upper dishrack had several places that were completing rusting out, just leaving the skins of the plastic coating in place. I ordered the upper dishrack - just the dishrack, none of the clips or other items shown in the schematic - and installed it pretty easily. One caution - this is JUST the upper dishrack. If you have two rows of tines that are clipped in and flip-flop back and forth on the left and right wider sides of the rack, you will need to order one or two pieces of part # PS 898500 as well. One of my tine rows was in salvageable shape, so I only needed to order one (in a second order upon discovering I it wasn't included). It wasn't difficult to figure out how the clips could come out and snap back in place. Just be careful, know that these are just plastic items and can break easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Moreno Valley, CA
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken Door Links
Remove two screws at top that fasten dishwasher to cabinet. Slide dishwasher out to expose the two links that attach the door to the springs. Fit the new links to the springs and door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from Wethersfield, CT
- Parts Used:
- W11196317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Seal on dishwasher worn out and coming loose.
Removed old seal, cleaned track, applied adhesive for new seal, seated new seal in track, closed door for 24 hours to allow adhesive to cure, then used dishwasher without difficulty. An easy repair.
Was this instruction helpful to you?
Thank you for voting!