58715193401 Kenmore Dishwasher - Instructions

The old gasket was worn. I pulled out the old one, put in the new gasket. I trimmed the ends to fit and that was it.

Simply took the old one out, and put the new one in.

Pulled off the old gasket and replaced it the same way with the new one.

Removed the two screws that mount to count top pulled the dishwasher out to see how the spring was attached , installed the new spring and the job was done the job it took about 15 mins. to complete.

I think the videos on the site are awesome. Made both repairs after watching them. They explain the repairs in a simple to follow way.

if the wire they snap on was bent it needs to be straightend.......they just snap on. easy to install but wish they had better wheels so this problem would be solved. My 2 sons have same brand dishwashers and have same problem.

I removed the two screws and then moved the dishwasher out a little bit (about 6 inches). I pushed the dishwasher toward one side to make room for me to change the spring with my hand and repeated the same procedure for the other side. After the spring change, I turned an old dishwasher to a new one.

I removed thr 4 screws behind the door that hold the control panel in place. Remove the panel and unplug the control module. Then remove 2 screws holding the module. Then carefully remove the module that is held by plastic clips- a butter knife worked well! Then just clip in new module and reverse steps. Thanks Partsselect for your prices and speed of delivery-saved us from doing a lot of dishes by hand!

1.Removed slide out dishes baskets, removed inside plastic food screen (just to clean) and disconnected electrical plug and hot water connection under the sink. 2. Unscrewed dishwasher retaining screws from kitchen counter top and slid dishwasher out (very easy). 3. Flipped dishwasher on its front. 4. Unhooked the 2 drain hoses and electrical connectors from the old drain pump, unscrewed it (torx screws) from the drain pump retainer bracket and replaced it with the new drain pump. 5. Cleaned the water jet pump (got all the accumulated crud out from the "impellers") and reinserted it in the dish washer. 5. Turned the dishwasher upright and reattached the hot water hose (using plumbers tape) and the electrical plug. 6. Finished pushing the dishwasher back under the counter, reattached the retaining screws to the counter top, turned it on and basked in the quietness of the dishwasher.

I removed the door panel and ran the dishwasher to determine where it was leaking. Ordered the parts. When parts arrived I removed door in order to get at the bottom door gasket, replace it, and removed the tube gasket and replaced it with new parts. The whole job was very easy for a person that's never repaired a dishwasher before. I also found that the return tube gasket at the top of the dishwasher was leaking and repaired that by making a new gasket out of a flat piece of rubber and an o-ring. All leaks have been repaired. With regards to the return tube issue, it may have only been loose and if so, I could have just tightened the return tube outlet and gotten the same results. The people at this site were excellent. Thank You

pulled out dishwasher ,left lines hooked ,started cicle .heard pump.took apart.seen problem. order new one ,works like new..

I used both epoxy on the male threads and then pulled out the case and twisted the flat car body flat kind of a nut. Let it sit for 36 hours and now like new.

Removed old hose and went to install new hose from Part Select. Part received was not the same as advertised. It was 6-8 inches shorter than the original hose. Would not make the necessary turns because of shorter length. I even went to Video instruction on installation even though I have been in Machine repair for 30 years , this video showed using the shorter hose and when installed in the video hose also had a kink because of hose length. Had to stop repair and go to hardware store and purchase a longer hose. This purchased hose from the hardware was 50% cheaper and actually worked. I also paid for 2-3 day shipping and received part 7 days later. I am very disappointed with Parts Select and am an owner of an Equipment Rental Facility and will never utilize Parts Select again.

Removed front panel of door, to get to the screws that hold the door on the hinges. Removed door, pulled gasket with pliers from bottom of door, not easy to get out because of mineral deposits. Had to push quite hard to get new gasket in. Put every thing back together and no leaks. I live in Alaska and I tried to order the part through Sears and they wanted $18.95 for shipping for a $12.87 part. The part with PartSelect was $14.92 but only $6.95 for shipping. I ordered the part on a Tuesday and recevied it on that Friday. We in Alaska get very tired of companies thinking we live on another planet. Thank you PartSelect.

Had trouble installing the new gasket at first. Fell inside the door, and would not stay in the groove intended for it. After watching the video on your website, learned is best to angle the gasket and work in slowly to the groove from one side. Much easier then