66517049402 Kenmore Dishwasher - Instructions

I am a 61 year old woman and it took me a total of 2 min. max. Popped it into place and pushed in button that holds it..Taa Daa...perfect!

The old tine row came out easily and the new one was easy to pop into place. I was pleased that it was so easy to order a replacement part.

put new hose on, very easy.

Just removed the old seal and followed the instructions that came with the new one. Since the old one didn't have any adhesive on it ,I didn't use the adhesice on the new one. Problem solved!

Remove 2 screws on lower baseplate. Remove 2 screws that hold dishwasher inside cabinet( may be attached to counter top or side cabinets). Turn off water supply to dishwasher. Remove any connections such as water supply, electrical connection, or waste water line that prevent dishwasher from being pulled out about 3/4 of the way. With the dishwasher door closed, remove broken parts and replace with new parts. Pull on spring to make final connection of nylon cable. Reverse the above instructions for re-installing the machine.

I took the unit apart to find out what was making the loud noise and found the seal on the main pump had been leaking ito the bearing on the motor.

Removed required hardware and dishwasher from undercounter mount. Turned dishwasher on its front and removed the old motor. Installed the new motor and tested for function. Installed once test was successful.

Watch your video about my dishwasher symptoms. Move water tube for upper rack to the right and release lower spray arm. Remove 4 clutch head screws from filter cover and remove. Dig out 10 years of undisolved soap and reassemble.

Remove the mounting screws that hold the dishwasher under the counter top. Remove dust cover plates at the bottom of the machine. The machine will have to be pulled out, so turn off the water to the machine. Usually under the kitchen sink. Disconnect water supply and push it out of the way so the dishwasher can be pulled out. Pull machine out enough so you have access to the door cables and springs. The door will have to be in the closed(up) position to do the repair. Usually only one side is broken. Start with the broken side and copy the working side when installing new parts. Then repair the working side. To get the working side apart just pull on the spring and disconnect it from the cable. Do the reverse to reinstall.

Took out the screws--found out what the problem was--ordered part (your people were helpfull--good customer people--received the part within the time I was told--installed according to the instructions--turned it on. . Working fine and guess what--I don't have to do the dishes anymore.

disconect water supply and drain hose, unscrew 2 screws hoding front of dishwasher to countertop, slide dischwasher out so you can tip on its door and remove 1 screw hidden behind plastic shield and pull motor out install in reverse order.

Removed the front control panel and control unit cover. Removed and disconected old control panel and installed the new panel. Very easy project, even though I didn't know what I was doing. Unfortunately this was not the problem. I had to also replace the heater element and Hi-Temp thermostat. Also easy replacements. The "Just Ask" option is well worth the money. It was a great help in diagnosing the problem.

first things first. troubleshoot.... unit wont run. no l.e.d.s at all. Opened front panel and first thing I see is a thermal cutout mounted outside of printed circuit board. After using a multimeter to check for continuity, used a set of alligator clips with a common lead, thus bypassing thermal cutout. Viola, she worked. Ordered part after finding site with google search. Part was delivered in two days.

Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.

When my dishwasher stopped working I went to the local appliance parts store with the entire button panel. I explained my situation to them, and the response was that I needed a new control panel -$68 and a week wait. So I ordered it. When it came in I noticed it was missing a button for the rinse only cycle. The parts guy said that maybe it was a problem with the parts vendor and ordered another one from their other vendor. In the mean time I installed the new control panel just to see if I would get any lights (no luck). A week later the new control panel came in - still no rinse only button. I got my money back and went home to see what I could find online. I ran across PartSelect - saw several comments describing my exact problem, and ordered a new fuse kit ($15). I put the original control panel back in, put in the new fuse (which took only 2 days to get to me!) and sure enough - problem solved.
Thanks PartSelect you have a great site with lots of useful information!

Steve in Colorado