66516033401 Kenmore Dishwasher - Instructions

put new hose on, very easy.

Removed the old tines by pushing out the clips on the end and then installed the new tines and applied clips - took 10 minutes worked slick and the washer basket looks to be brand.

Looked under machine, saw wire going to heater was burned off.Seal on heater failed, water leaked onto terminal, shorted and burned, ruined plastic terminal nut.Replaced heater and wire terminal, and nut, took minutes, works great.

Watch your video about my dishwasher symptoms. Move water tube for upper rack to the right and release lower spray arm. Remove 4 clutch head screws from filter cover and remove. Dig out 10 years of undisolved soap and reassemble.

When my dishwasher stopped working I went to the local appliance parts store with the entire button panel. I explained my situation to them, and the response was that I needed a new control panel -$68 and a week wait. So I ordered it. When it came in I noticed it was missing a button for the rinse only cycle. The parts guy said that maybe it was a problem with the parts vendor and ordered another one from their other vendor. In the mean time I installed the new control panel just to see if I would get any lights (no luck). A week later the new control panel came in - still no rinse only button. I got my money back and went home to see what I could find online. I ran across PartSelect - saw several comments describing my exact problem, and ordered a new fuse kit ($15). I put the original control panel back in, put in the new fuse (which took only 2 days to get to me!) and sure enough - problem solved.
Thanks PartSelect you have a great site with lots of useful information!

Steve in Colorado

Opened dishwasher door,removed 6 Torx screws, changed out panel, replaced screws. VERY SIMPLE

Removed old tine rows and replaced with the new parts. No tools were needed. Each was replaced one at a time so the old ones could serve as a model for how the new ones were inserted and attached. Not much more complicated than changing a light bulb. Parts appear to be good original equipment quality but quite pricy for these very simple pieces.

You only need to pull it out about 6 to 8 inches and you don’t need to disconnect anything to slide it on

Snapped the new stops on. It took about 2 minutes.

Removed the front control panel and control unit cover. Removed and disconected old control panel and installed the new panel. Very easy project, even though I didn't know what I was doing. Unfortunately this was not the problem. I had to also replace the heater element and Hi-Temp thermostat. Also easy replacements. The "Just Ask" option is well worth the money. It was a great help in diagnosing the problem.

First I identified the problem by checking the plug ends of the heater coil with an ohm meter. I quickly odered the part and when it arrived a few days later, I simply pulled off the electrical connectors, unscrewed the two bolts, removed the old/broken coil, put in the new coil and tightened down the nuts snuggly.
Nothing to it. I then had to reset the error code and it is working like new.

Removed old part and replaced with new part

First of all I appreciate the instructions provided by this site when I selected the part I needed! The installation was so easy. I popped the end caps off of the top rack guides and removed the top rack. I reach in and popped the clips holding the top sprayer bar and gently pulled down on the sprayer bar enough to place the spinner button in the top of the sprayer bar. Then pressed the spinner on the bottom of the sprayer bar into the button I place in the top of the sprayer bar and reattached the sprayer bar to the clips. Put the top rack back on the guides and replaced the guide caps and it was finished. Easy fix thanks to this site great instructions!

Took out the screws--found out what the problem was--ordered part (your people were helpfull--good customer people--received the part within the time I was told--installed according to the instructions--turned it on. . Working fine and guess what--I don't have to do the dishes anymore.

disconect water supply and drain hose, unscrew 2 screws hoding front of dishwasher to countertop, slide dischwasher out so you can tip on its door and remove 1 screw hidden behind plastic shield and pull motor out install in reverse order.