58714144404 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dante from SOUTHOLD, NY
- Parts Used:
- 809006501
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Broken BOTTOM door gasket
1-2-3. Finished ! I had watched your video on how to !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Prfovincetown, MA
- Parts Used:
- 809006501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
leaking bottom door gasket
Used pliers to pull out the old gasket. New gasket snapped into place. Notice where notches in the gasket are when the old one is removed, so the new one can be properly oriented. It was not necessary to remove the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Woodburn, OR
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher was leaking at the front, just below the door
I measured the length of the gasket, using the old one to measure the length. Cut it to that length and installed it. VERY SIMPLE TO DO! But it didn't stop my leak--turns out there was a small leak in the bottom of the tub that was easily fixed with some silicone. The dishwasher's like new now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theodore from Great Falls, MT
- Parts Used:
- 154574401
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Soap dish latch worn out
Removed front cover. No instructions so I removed all the screws. Only the bottom 2 need to be removed(1 on each side) then push cover up to unlatch. Remove 2 wires and 6 screws. Replace soap dish unit. reinstall screws and wires. Replace front cover. The hardest part is the front cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheila from Pelzer, SC
- Parts Used:
- A00126501
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Wouldn't drain water out after washing
Removed the screws at the top which held it in , then I pulled it outside of it's shell, took it apart and took the drain part off, replaced with new drain part, put it back together the same way I took it off, pushed it back in, put the screws back in, tested it, and it worked. Ta Daaa!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felipe from Poughkeepsie, NY
- Parts Used:
- 154574401
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Cap would not close
At first I wasn't sure; I thought I had to buy the inner panel of the door. Considering that I have to minimize expenses I made it a point to tackle the problem myself. I unscrewed the outter panel off the dishwasher door and located the dispenser from inside of the inner door panel.
I unplugged the old dispenser,which was damaged, unscrewed it from the panel and removed it. I cleaned any and all debris, dirt and soap scum it had accumilated over the short years we've owned it.
Finally; after I prepared the new dispenser for installation, I placed it in position screwed it in and plugged it in, which was slightly tricky because it is pretty snug against the inside door panel. Once installed, I got my older son, 15, to help me screw in the outside panel of the door, and as he held it I screwed it on the the inside panel.
I tested it with no dishes inside by pouring just a little detergent in the new dispenser, starting the dishwasher and I stuck around in case there were any leaks or any other possible disaster that could occur.
This was exactly one week ago and all is still well. By the way, the person who took my order, I believe her name was Joann, was great. She talked to me making certain I had the right part, which I was unsure of since the diagram on your site was not quite clear. On top of that; I didn't pay for overnight service, yet my part was at my door the next day. I was amazed at the quick service and delivery. Thanks Joann!!!
Felipe,
Poughkeepsie, NY
I unplugged the old dispenser,which was damaged, unscrewed it from the panel and removed it. I cleaned any and all debris, dirt and soap scum it had accumilated over the short years we've owned it.
Finally; after I prepared the new dispenser for installation, I placed it in position screwed it in and plugged it in, which was slightly tricky because it is pretty snug against the inside door panel. Once installed, I got my older son, 15, to help me screw in the outside panel of the door, and as he held it I screwed it on the the inside panel.
I tested it with no dishes inside by pouring just a little detergent in the new dispenser, starting the dishwasher and I stuck around in case there were any leaks or any other possible disaster that could occur.
This was exactly one week ago and all is still well. By the way, the person who took my order, I believe her name was Joann, was great. She talked to me making certain I had the right part, which I was unsure of since the diagram on your site was not quite clear. On top of that; I didn't pay for overnight service, yet my part was at my door the next day. I was amazed at the quick service and delivery. Thanks Joann!!!
Felipe,
Poughkeepsie, NY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bar Seven A Companies Attn: C from REDMOND, OR
- Parts Used:
- 154290204
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Dishes would not dry. Electrical burning smell.
Removed dishwasher and looked for component that had gotten hot. Saw partially melted connector on thermostat. Removed and replaced thermostat. Replaced female spade connector on wire. Replaced dishwasher.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher was making screeching sound.
Disconnected the water line. Pulled the dishwasher out from underneath the counter. Turned the dishwasher on its side. Removed the two screws that were holding the motor in place with a special screwdriver set I had to buy. Removed the motor. Found that the front O-ring on the motor was mangled. Replaced the O-ring. No more screeching. The dishwasher now cleans the dishes better than the day I first bought it. I have to wonder if that O-ring was ever installed properly from the factory.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Jane from Niles, MI
- Parts Used:
- 809006501
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver
dishwasher was leaking onto the floor
We received the part in just a day or two so thank you for quick delivery. The base of the dishwasher door was leaking...not the actual gasket but a long strip at the base of the door had separated. With the help of a talented neighbor, my husband and our good neighbor pulled the dishwasher out from its installed place, took off the door and found a screw which needed a star-shaped screwdriver. Fortinately another neighbor had just the right tool....so screw was removed, old strip pulled out, new strip slid into place, door re-attached, dishwasher shoved back into place and anchored as though everyone knew what they wre doing! It works fine now....a small leak continued the first few washings but all is perfect now. We hope it lasts....and lasts.....and lasts! Thanks. Happy Wife
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Water Mill, NY
- Parts Used:
- 154662601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
strike was broken
Easy as pie. I tokk the screws out that held the dishwasher to the counter top out. Then removed the screws holding the strike in place, inserted the new one, installed screws and then rescrewed the 2 screws backintothe countertop. Job done. All told 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Sacramento, CA
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gasket leak
First I pulled out the old gasket and replaced with the new one. The new one is too long on purpose but only had to be trimmed a little for a perfect fit. Very easy and now no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray D from LAWRENCEBURG, TN
- Parts Used:
- 809006501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Leak at door
As shown on you tube
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from KIOWA, CO
- Parts Used:
- 809006501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
leaking at bottom door on to the floor
i removed the bottom dish tray, Found the plastic gasket, gave a tug with my needle nose pliers and pulled it out. laid it on the door to make certain that i placed the new one in exactly as the old one came out.pushed it in and set the dishwasher to wash to check i had it in correctly. WALLA instant satisfaction.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert e from HOPATCONG, NJ
- Parts Used:
- 154430501
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
broken door spring on dishwasher
used pliers to hook up spring according to repair video.5 mins to check for proper tension.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from SHELOCTA, PA
- Parts Used:
- 809006501
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Leaking water
followed online video provided and it was a snap
Was this instruction helpful to you?
Thank you for voting!